Search arXiv⌕ Search
Home/Archive/arXiv

arXiv · 1706.05917

Transmission line parameter identification using PMU measurements

Di Shi·Daniel J. Tylavsky·Kristian M. Koellner·Naim Logic·David E. Wheeler
View original source ↗Read source document ↗Export metadata ↓

Abstract

Accurate knowledge of transmission line (TL) impedance parameters helps to improve accuracy in relay settings and power flow modeling. To improve TL parameter estimates, various algorithms have been proposed in the past to identify TL parameters based on measurements from Phasor Measurement Units (PMUs). These methods are based on the positive sequence TL models and can generate accurate positive sequence impedance parameters for a fully-transposed TL when measurement noise is absent; however these methods may generate erroneous parameters when the TLs are not fully transposed or when measurement noise is present. PMU field-measure data are often corrupted with noise and this noise is problematic for all parameter identification algorithms, particularly so when applied to short transmission lines. This paper analyzes the limitations of the positive sequence TL model when used for parameter estimation of TLs that are untransposed and proposes a novel method using linear estimation theory to identify TL parameters more reliably. This method can be used for the most general case: short or long lines that are fully transposed or untransposed and have balanced or unbalance loads. Besides the positive or negative sequence impedance parameters, the proposed method can also be used to estimate the zero sequence parameters and the mutual impedances between different sequences. This paper also examines the influence of noise in the PMU data on the calculation of TL parameters. Several case studies are conducted based on simulated data from ATP to validate the effectiveness of the new method. Through comparison of the results generated by this novel method and several other methods, the effectiveness of the proposed approach is demonstrated.

Explore related subjects

eess.SYcs.SY

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Di Shi, Daniel J. Tylavsky, Kristian M. Koellner, Naim Logic, David E. Wheeler. 2017-06-15. Transmission line parameter identification using PMU measurements. https://doi.org/10.1002/etep.522

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related papers

arXiv2026

Safe learning-based control via function-based uncertainty quantification

Uncertainty quantification is essential when deploying learning-based control methods in safety-critical systems. This is commonly realized by constructing uncertainty tubes that enclose the unknown function of interest, e.g., the reward and constraint functions or the underlying dynamics model, with high probability. However, existing approaches for uncertainty quantification typically rely on restrictive assumptions that encode smoothness properties of the unknown function, such as a known norm in a function space. Moreover, these methods usually struggle with discontinuities. In this paper, we model the unknown function as a random function from which independent and identically distributed realizations can be generated. We then construct uncertainty tubes via the scenario approach that hold with high probability. Our uncertainty tubes rely solely on sampled realizations and can therefore accommodate discontinuities represented by the sampling model. We integrate these uncertainty tubes into a safe Bayesian optimization algorithm with which we safely tune control parameters on a real Furuta pendulum.

eess.SY↗
arXiv2026

Enhanced ShockBurst for Ultra Low-Power On-Demand Sensing

On-demand sensing requires battery-powered Internet-of-Things (IoT) and implantable medical devices to remain in deep sleep and activate wireless communication only when data transmission is required. In such systems, battery lifetime depends strongly on radio active time. This work investigates how communication architecture and physical layer (PHY) configuration influence radio active time by comparing connection-oriented Bluetooth Low Energy (BLE) with connectionless Enhanced ShockBurst (ESB) on identical BLE-compatible hardware. Under identical 2 Mbps PHY configurations, ESB reduces wake-up latency and energy consumption to approximately one-twentieth of BLE by eliminating connection establishment and maintenance overhead. Increasing the ESB PHY rate from 2 to 4 Mbps further shortens packet airtime by approximately 52% and reduces transmission energy by approximately 43%. Finally, a first-in, first-out (FIFO)-triggered implantable loop recorder prototype demonstrates that jointly optimizing communication architecture, PHY configuration, and buffered transmission enables sleep-wake operation and reduces total system power consumption by approximately 60% compared with conventional BLE operation. These results identify minimizing radio active time as a key design principle for ultra-low-power on-demand sensing and provide practical guidance for battery-powered sensing systems.

eess.SY↗
arXiv2026

Receding Horizon Multi-Agent Deceptive Path Planner

Deceptive path planning enables autonomous agents to obscure their true goals from observers by deviating from an expected optimal path. Prior work largely solves full-horizon, end-to-end optimization for single agents, which is expensive to recompute online and difficult to scale or adapt en route. We propose a unified framework for deceptive path planning using a Boltzmann distribution, computing over short-horizon candidate trajectories within a receding-horizon loop. By param- By iterating a user-defined cost that captures deception, resources, and smoothness, and optionally includes coupling terms between agents, the framework yields stochastic policies that balance the tradeoff between optimal paths and deceptive deviation. Policies are updated locally and do not require training. The level of deception and adherence to constraints can be dynamically tuned, enabling online adaptation to changes in goals and constraints such as obstacles. This step-by-step tuning opens the door to new forms of dynamic deception. Simulation studies demonstrate the flexibility of our approach, maintaining deception while adapting to environmental and constraint updates, avoiding the recomputation required by full-horizon methods, and supporting intuitive tuning via a small set of parameters

eess.SY↗