Search arXiv⌕ Search
Home/Archive/arXiv

arXiv · 2401.01406

Influence of Surface Roughness on Linear Behavior and Mechanical Properties of Three Cyanoacrylate-Based Adhesives Used to Bond Strain Gages

L. G. Simao·W. P. Jesus·M. E. A. Ribeiro·H. C. Rangel·R. J. S. Rodriguez·E. A. Carvalho
View original source ↗Read source document ↗Export metadata ↓

Abstract

The challenge of accessing specialized adhesives designed for strain gage applications has been highlighted due to failures in logistic chains, requiring the exploration of local alternatives. A direct simulation of strain gage bonding behavior with two steel plates is infeasible due to the unique construction of strain gages. Therefore, an indirect simulation method, comparing local alternatives to a widely accepted adhesive, Loctite 496, was employed in this study. Two potential replacements, Loctite 401 and Tekbond 793, were tested and matched against the benchmark adhesive, with a focus on the key mechanical properties: Proportional Shear Strain (PSS), Proportional Shear Stress (PSSt), and Apparent Shear Modulus (G*). Loctite 401 exhibited the highest G*, suggesting its potential use in strain gage installations if G* is considered most important. However, Tekbond 793 demonstrated superior PSS, Maximum Shear Stress (MSSt), and Rupture Shear Stress (RSSt) performance, displaying linear behavior even without an accelerator. Surface preparation considerations were also discussed, noting that hand abrading results in double the surface roughness than using an orbital sander. The study further identified two main regions concerning failure modes related to Ra, with values below 0.31 μm causing significant variations in observed mechanical properties, pointing towards factors beyond adhesive layer thickness affecting bond properties. Lastly, the general recommendation is the use of an accelerator for all tested adhesives, while the use of a surface conditioner and neutralizer was found to negatively impact adhesive performance.

Explore related subjects

cond-mat.soft

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

L. G. Simao, W. P. Jesus, M. E. A. Ribeiro, H. C. Rangel, R. J. S. Rodriguez, E. A. Carvalho. 2024-01-02. Influence of Surface Roughness on Linear Behavior and Mechanical Properties of Three Cyanoacrylate-Based Adhesives Used to Bond Strain Gages. https://arxiv.org/abs/2401.01406

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related papers

arXiv2026

Spontaneous Vortex Instability in Active Nematics

One of the defining results in the study of active matter is the spontaneous flow instability, through which a homogeneous, uniformly aligned state breaks translational symmetry along a single direction and develops sustained flow. The vortex state that emerges at higher activity has instead been attributed to nonlinear dynamics. Using a Floquet-type linear stability analysis, we show that no such mechanism is required: the flowing state undergoes a secondary, zigzag instability that breaks the remaining translational symmetry and produces the vortex state. We further identify a regime in which the flowing state ceases to exist and vortices emerge directly from the uniformly aligned state. Under channel confinement, the instability selects a length scale that differs from the establishedactivelengthscale, andsetsthenumberofvorticesthatappear, leadingtoaconfinement- selected pattern reminiscent of a vortex lattice, opening a route toward direct experimental tests of this instability. Full nonlinear simulations reproduce the predicted onset activities and the selected vortex number.

cond-mat.soft↗
arXiv2026

Active pistons extract work by periodic compression alone

Active matter is liable to invent protocols that evade the constraints of equilibrium thermodynamics. We put forward active pistons that extract work by periodic compression alone without changing any bulk property of the system. Such pistons necessarily couple the perturbation imposed by an external operator with some degrees of freedom internal to active components. We illustrate this design principle with elastic networks composed of self-aligning motile particles. For slow protocols, self-alignment always overwhelms mechanical friction when the internal activity exceeds a specific threshold controlled by fluctuations. We identify the key response coefficient that helps delineate regimes of work extraction, and reveal that the corresponding phase diagram follows a master curve with re-entrance in terms of noise amplitude. Overall, our active pistons embody a novel design principle with broad implications for building innovative engines far from equilibrium.

cond-mat.soft↗
arXiv2026

Geometry-induced flocking and topological sound on a defect-free curved surface

We study an ordered polar active flock on a torus and show that topological sound persists on a compact curved surface without topological defects or physical boundaries. Using the covariant Toner Tu theory, we derive an effective nonHermitian Dirac operator whose curvature-induced mass changes sign across the outer and inner equators, producing two Jackiw Rebbi domain walls. These support co-propagating but distinct chiral edge excitations: a density mode localized on the positively curved outer equator and a Goldstone mode localized on the negatively curved inner equator. The bulk bands possess opposite half-integer Chern numbers whose jumps across the domain walls are determined by the sign of the Gaussian curvature. We further show that the localised modes are protected by a one-dimensional Callias index theorem, while the sum of the local indices obeys the Poincare Hopf theorem on the compact surface. Our results establish that curvature alone, independent of defects and boundaries, is sufficient to generate and protect topological sound in active matter, providing a unified connection between non-Hermitian topology, differential geometry, and hydrodynamic theory of collective motion.

cond-mat.soft↗