Search arXiv⌕ Search

arXiv · 2611.09489

The ATAR, a dense and compact vertex detector for the PIONEER experiment

Abstract

PIONEER is an approved experiment at the Paul Scherrer Institut (PSI) in Villigen, Switzerland that aims to measure the charged-pion branching ratio to electrons vs. muons with an accuracy of 0.01%. This is an order of magnitude improvement in precision compared to its predecessors and approaches the accuracy of the standard model prediction. The key elements of PIONEER are a high resolution calorimeter built concentrically around the high granularity active target (ATAR). The ATAR is composed of a stack of 48 low gain avalanche strip detectors (LGADs) to stop the beam pions and provide detailed information of the event topology. This will include precise timing (in the order of 200ps), spatial information (to an accuracy of about 60 micro meter) and pulse height information with a high dynamic range to separate pion stops from muons and MIPs. To avoid affecting the energy measurement of the positrons, the readout electronics is placed outside the acceptance angle of the calorimeter. It is composed of a fast amplifier and a fast sampling chip digitizing the LGAD wave form for real time analysis. The paper describes the PIONEER-experiment with focus on the ATAR and its readout. The status of the development and activities in 2026 will be reported.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Tilman Rohe, for the PIONEER collaboration. 2026-11-06. The ATAR, a dense and compact vertex detector for the PIONEER experiment. https://arxiv.org/abs/2611.09489

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related papers

A Low-Complexity 200 Mbit/s Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation

Modern full-duplex communication systems, such as Gigabit Ethernet, enable high data rates over challenging transmission media but require sophisticated circuitry and non-trivial digital interfaces. For laboratory instrumentation, the objective may instead be to achieve moderate-bandwidth full-duplex communication over short, well-controlled coaxial cables with minimal circuit and interface complexity. We present a low-complexity bidirectional digital interconnect that enables simultaneous transmission and reception of baseband logic signals over a single coaxial cable. The circuit combines a discrete passive resistive hybrid providing line termination and directional separation, a single logic gate as line driver, and a commercial differential receiver used as a comparator. No modulation, transformer coupling, adaptive calibration, or active analog or digital echo cancellation is required. The design target is full-duplex operation at 200 MBit/s over 10 m of standard RG-178 cable. An analytical treatment of the hybrid network determines the system parameter that maximizes the differential signal amplitude at the receiver, while circuit simulations predict the deterministic timing errors resulting from imperfect directional separation. Experimental measurements confirm the predicted deterministic jitter and show good agreement with the simulation results. For typical laboratory coaxial cables up to 10 m, the measured peak-to-peak edge timing error remains below 1.2 ns. A bidirectional transmission experiment with randomized data demonstrates a clearly open eye diagram. It was found that the transceiver inherently provides loopback functionality when the transmission line is left open. The proposed approach provides a simple, protocol-independent bidirectional physical link which may be useful in laboratory instrumentation where cable routing is constrained.

physics.ins-det↗

Photoluminescence of resin-based solder flux residue under ultraviolet excitation from 120 nm to 310 nm

Nuisance photoluminescence is a potential source of background in particle detectors that use noble liquids as target material for galactic dark matter particles and neutrinos. Liquid argon and xenon scintillate in the vacuum ultraviolet (VUV) wavelength range in response to particle interactions. Photoluminescent materials that absorb these photons can cause unexpected signals that may impede event reconstruction in these detectors. We illuminated residue from different types of commercial solder flux commonly used in liquid xenon detectors with ultraviolet and VUV light and measured their photoluminescence spectra and intensities. We find that all tested flux residues photoluminesce in the visible spectral region when exposed to VUV light.

physics.ins-det↗

A toy model for understanding the space-point resolution of silicon pixel detectors with digital readout

Silicon pixel detectors are widely used in high-energy physics experiments as tracking detectors close to the primary interaction vertex. They provide excellent space-point resolution together with fast electronic readout. Many of them employ only digital (binary) readout which makes the applicability of centre-of-gravity algorithms less obvious. Charge sharing between neighboring pixels improves the resolution beyond the single-pixel limit, but in practice there is a lack of quantitative understanding of the achievable gains. This work provides a simplified analytical and numerical model with which the maximum improvement achievable through charge sharing is quantified for both one and two-dimensional pixel geometries. A phenomenological parameterisation of the resolution as a function of the average cluster size is derived and compared to experimental data from several detector technologies.

physics.ins-det↗