Search arXiv⌕ Search
Home/Archive/arXiv

arXiv · physics/0603034

Stray Field Magnetic Resonance Tomography using Ferromagnetic Spheres

Mladen Barbic·Axel Scherer
View original source ↗Read source document ↗Export metadata ↓

Abstract

The methodology for obtaining two- and three-dimensional magnetic resonance images by using azimuthally symmetric dipolar magnetic fields from ferromagnetic spheres is described. We utilize the symmetric property of a geometric sphere in the presence of a large externally applied magnetic field to demonstrate that a complete two- or three-dimensional structured rendering of a sample can be obtained without the motion of the sample relative to the sphere. Sequential positioning of the integrated sample-sphere system in an external magnetic field at various angular orientations provides all the required imaging slices for successful computerized tomographic image reconstruction. The elimination of the requirement to scan the sample relative to the ferromagnetic tip in this imaging protocol is a potentially valuable simplification compared to previous scanning probe magnetic resonance imaging proposals.

Explore related subjects

physics.ins-detphysics.med-ph

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Mladen Barbic, Axel Scherer. 2006-03-05. Stray Field Magnetic Resonance Tomography using Ferromagnetic Spheres. https://doi.org/10.1016/j.jmr.2006.05.001

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related papers

arXiv2026

A Low-Complexity 200 Mbit/s Full-Duplex Digital Link Over a Single Coaxial Cable for Laboratory Instrumentation

Modern full-duplex communication systems, such as Gigabit Ethernet, enable high data rates over challenging transmission media but require sophisticated circuitry and non-trivial digital interfaces. For laboratory instrumentation, the objective may instead be to achieve moderate-bandwidth full-duplex communication over short, well-controlled coaxial cables with minimal circuit and interface complexity. We present a low-complexity bidirectional digital interconnect that enables simultaneous transmission and reception of baseband logic signals over a single coaxial cable. The circuit combines a discrete passive resistive hybrid providing line termination and directional separation, a single logic gate as line driver, and a commercial differential receiver used as a comparator. No modulation, transformer coupling, adaptive calibration, or active analog or digital echo cancellation is required. The design target is full-duplex operation at 200 MBit/s over 10 m of standard RG-178 cable. An analytical treatment of the hybrid network determines the system parameter that maximizes the differential signal amplitude at the receiver, while circuit simulations predict the deterministic timing errors resulting from imperfect directional separation. Experimental measurements confirm the predicted deterministic jitter and show good agreement with the simulation results. For typical laboratory coaxial cables up to 10 m, the measured peak-to-peak edge timing error remains below 1.2 ns. A bidirectional transmission experiment with randomized data demonstrates a clearly open eye diagram. It was found that the transceiver inherently provides loopback functionality when the transmission line is left open. The proposed approach provides a simple, protocol-independent bidirectional physical link which may be useful in laboratory instrumentation where cable routing is constrained.

physics.ins-det↗
arXiv2026

Photoluminescence of resin-based solder flux residue under ultraviolet excitation from 120 nm to 310 nm

Nuisance photoluminescence is a potential source of background in particle detectors that use noble liquids as target material for galactic dark matter particles and neutrinos. Liquid argon and xenon scintillate in the vacuum ultraviolet (VUV) wavelength range in response to particle interactions. Photoluminescent materials that absorb these photons can cause unexpected signals that may impede event reconstruction in these detectors. We illuminated residue from different types of commercial solder flux commonly used in liquid xenon detectors with ultraviolet and VUV light and measured their photoluminescence spectra and intensities. We find that all tested flux residues photoluminesce in the visible spectral region when exposed to VUV light.

physics.ins-det↗
arXiv2026

A toy model for understanding the space-point resolution of silicon pixel detectors with digital readout

Silicon pixel detectors are widely used in high-energy physics experiments as tracking detectors close to the primary interaction vertex. They provide excellent space-point resolution together with fast electronic readout. Many of them employ only digital (binary) readout which makes the applicability of centre-of-gravity algorithms less obvious. Charge sharing between neighboring pixels improves the resolution beyond the single-pixel limit, but in practice there is a lack of quantitative understanding of the achievable gains. This work provides a simplified analytical and numerical model with which the maximum improvement achievable through charge sharing is quantified for both one and two-dimensional pixel geometries. A phenomenological parameterisation of the resolution as a function of the average cluster size is derived and compared to experimental data from several detector technologies.

physics.ins-det↗