Search arXiv⌕ Search

arXiv subjects

M. Fuchs

Publications and source records attributed to M. Fuchs.

At least 19 recordsLinked to original sources
arXiv2026

Serenity-S1, a CMS Tracker Readout and Data Processing Card for HL-LHC

The CERN Large Hadron Collider will be upgraded to the High-Luminosity LHC, increasing the particle-collision rate and the demands on detector readout. A key element of this upgrade is the new CMS Tracker, whose silicon sensors will generate data at an aggregate rate of about 10 TB/s. This data must be routed efficiently to processing systems and filtered before storage. Serenity-S1 is an ATCA readout and data-processing card based on an AMD Virtex UltraScale+ VU13P FPGA with 128 high-speed serial transceivers. Twenty 12-channel Samtec FireFly optical modules provide up to 120 transmit and 120 receive channels at line rates of up to 25 Gb/s, while an additional optical module supports CMS Tracker links at up to 10 Gb/s per channel. The modular optical layout, combined with the large FPGA, makes Serenity-S1 suitable for several applications within and beyond CMS. ATCA provides the power and cooling required for operation in the CMS service cavern. Low-level management and the IPMI interface are provided by an OpenIPMC mezzanine, while an AMD Kria K26 system-on-module running AlmaLinux 9 performs higher-level board management and application control. Firmware and software frameworks provide common infrastructure so that users can focus on application-specific logic. The paper describes the hardware, firmware and software architecture of Serenity-S1 and its deployment in CMS Tracker integration and R&D activities.

physics.ins-det↗
arXiv2026

Report on the Advanced Linear Collider Study Group (ALEGRO) Workshop 2026

The 7th ALEGRO workshop, hosted by INFN Frascati National Laboratories from 3rd to 5th March 2026, brought together the international Advanced Novel Accelerators (ANA) community to discuss the role of advanced wakefield accelerators (AWA) in particle and high-energy physics. Organized under the ICFA-ANA panel, the workshop highlighted recent progress in plasma- and structure-based wakefield acceleration and strengthened international collaboration toward future energy-frontier colliders. A major focus was the ongoing 10 TeV linear collider design study, launched in 2025 following the US P5 recommendations. A dedicated session covered accelerator concepts, enabling technologies, and the associated physics case, while recognizing that future priorities will depend on the outcome of the European Strategy for Particle Physics Update. The workshop also reviewed nearer-term applications of advanced accelerators, including fixed-target experiments, injectors for future colliders and light sources, plasma-based Higgs factory concepts, and proton-driven plasma wakefield acceleration. Beyond high-energy physics, sessions covered free-electron lasers, synchrotron light sources, and strong-field QED. Recent demonstrations of FEL lasing with plasma-accelerated electron beams highlighted significant progress in beam quality and accelerator performance. Operational challenges for reliable user facilities, including high-availability laser and electron-beam systems, were discussed alongside the growing role of artificial intelligence and machine learning for accelerator optimization and control. This report summarizes the workshop discussions and conclusions from the chairs, together with short contributions from the presenters, providing an overview of the current status and future prospects of advanced wakefield accelerators.

physics.acc-ph↗
arXiv2024

Nonlinear microrheology with time-dependent forces -- Application to recoils in viscoelastic fluids

This work presents a theoretical analysis of the motion of a tracer colloid driven by a time-dependent force through a viscoelastic fluid. The recoil of the colloid after application of a strong force is determined. It provides insights into the elastic forces stored locally in the fluid and their weakening by plastic processes. We generalize the mode coupling theory of microrheology to include time-dependent forces. After deriving the equations of motion for the tracer correlator and simplifying to a schematic model we apply the theory to a switch-off force protocol that features the recoiling of the tracer after cessation of the driving. We also include Langevin dynamics simulations to compare to the results of the theory. A non-monotonic trend of the recoil amplitude is found in the theory and confirmed in the simulations. The linear-response approximation is also verified in the small-force regime. While the overall agreement between simulation and theory is good, simulation shows that the theory predicts a too strong non-monotonous dependence of the recoil distance on the applied force.

cond-mat.soft↗
arXiv2024

ZynqMP-based board-management mezzanines for Serenity ATCA-blades

In the context of the CMS Phase-2 tracker back-end processing system, two mezzanines based on the Zynq Ultrascale+ Multi-Processor System-on-Chip (MPSoC) device have been developed to serve as centralized slow control and board management solution for the Serenity-family \textcolor{black}{Advanced Telecommunications Computing Architecture (ATCA)} blades. This paper presents the developments of the MPSoC mezzanines to execute the Intelligent Platform Management Controller (IPMC) software in the real-time capable processors of the MPSoC. In coordination with the Shelf Manager, once full-power is enabled, a CentOS-based Linux distribution is executed in the application processors of the MPSoC, on which EMPButler and the Serenity Management Shell (SMASH) are running.

physics.ins-det↗
arXiv2023

Lessons learned while developing the Serenity-S1 ATCA card

The Serenity-S1 is a Xilinx Virtex Ultrascale+ based Advanced Telecommunications Computing Architecture (ATCA) processing blade that has been optimised for production. It incorporates many developments from the Serenity-A and Serenity-Z prototype cards and, where possible, adopts solutions being used across CERN. It also uses many new parts because commonly used parts have disappeared from the market during the semiconductor crisis, with only some returning. Improvements to simplify manufacture, the performance of new components, some of the more difficult aspects of procurement, the performance of production-grade Samtec 25\,Gb/s optical firefly parts, and issues with the rack cooling infrastructure are discussed.

physics.ins-det↗
arXiv2022

Snowmass Whitepaper AF6: Plasma-Based Particle Sources

High-brightness beams generated by particle sources based on advanced accelerator concepts have the potential to become an essential part of future accelerator technology. High-gradient accelerators can generate and rapidly accelerate particle beams to relativistic energies while minimizing irreversible detrimental effects to the beam brightness that occur at low beam energies. Due to the high accelerating gradients, these novel accelerators are also significantly more compact than conventional technology. The beam parameters of these particle sources are largely determined by the injection and subsequent acceleration processes. While there has been significant progress crucial parameters that are required for a future collider or more near-term applications, including X-ray free-electron lasers (XFELs), such as a sufficiently small energy spread and small emittance for bunches with a high charge and at high pulse repetition rate. Major research and development efforts are required to realize these approaches for a front-end injector for a future collider in order to address these limitations. In particular, this includes methods to control and manipulate the phase-space and spin degrees-of-freedom of ultrashort LWFA electron bunches with high accuracy, methods that increase the laser-to-electron beam efficiency and increased repetition rate. This also includes the development of high-resolution diagnostics, such as full 6D phase-space measurements, beam polarimetry and high-fidelity simulation tools. A further increase in beam luminosity can be achieve through emittance damping. For future colliders, the damping rings might be replaced by a substantially more compact plasma-based approach. Here, plasma wigglers are used to achieve similar damping performance but over a two orders of magnitude reduced length.

physics.acc-ph↗
arXiv2021

The direct correlation function of a crystalline solid

Direct correlation functions (DCFs), linked to the second functional derivative of the free energy with respect to the one-particle density, play a fundamental role in a statistical mechanics description of matter. This holds in particular for the ordered phases: DCFs contain information about the local structure including defects and encode the thermodynamic properties of crystalline solids; they open a route to the elastic constants beyond low temperature expansions. Via a numerical tour de force we have explicitly calculated for the first time the DCF of a solid: based on the fundamental measure concept we provide results for the DCF of a hard sphere crystal. We demonstrate that this function differs at coexistence significantly from its liquid counterpart - both in shape as well as in its order of magnitude - because it is dominated by vacancies. We provide evidence that the traditional use of liquid DCFs in functional Taylor expansions of the free energy is conceptually wrong and show that the emergent elastic constants are in good agreement with simulation-based results.

cond-mat.soft↗
arXiv2021

Cratering of Soil by Impinging Jets of Gas, with Application to Landing Rockets on Planetary Surfaces

Several physical mechanisms are involved in excavating granular materials beneath a vertical jet of gas. These occur, for example, beneath the exhaust plume of a rocket landing on the soil of the Moon or Mars. A series of experiments and simulations have been performed to provide a detailed view of the complex gas/soil interactions. Measurements have also been taken from the Apollo lunar landing videos and from photographs of the resulting terrain, and these help to demonstrate how the interactions extrapolate into the lunar environment. It is important to understand these processes at a fundamental level to support the on-going design of higher-fidelity numerical simulations and larger-scale experiments. These are needed to enable future lunar exploration wherein multiple hardware assets will be placed on the Moon within short distances of one another. The high-velocity spray of soil from landing spacecraft must be accurately predicted and controlled lest it erosively damage the surrounding hardware.

astro-ph.EP↗
arXiv2019

Multiple Fourier Component Analysis of X-ray Second Harmonic Generation in Diamond

The unprecedented brilliance of X-ray free-electron lasers (XFELs) [1, 2] has enabled first studies of nonlinear interactions in the hard X-ray range. In particular, X-ray-optical mixing [3], X-ray second harmonic generation (XSHG) [4] and nonlinear Compton scattering (NLCS) [5] have been recently observed for the first time using XFELs. The former two experiments as well as X-ray parametric downconversion (XPDC)[6, 7] are well explained by nonlinearities in the impulse approximation[8], where electrons in a solid target are assumed to be quasi free for X-ray interactions far from atomic resonances. However, the energy of the photons generated in NLCS at intensities reaching up to 4 x 1020 W/cm2 exhibit an anomalous red-shift that is in violation with the free-electron model. Here we investigate the underlying physics of X-ray nonlinear interactions at intensities on order of 1016 W/cm2. Specifically, we perform a systematic study of XSHG in diamond. While one phase-matching geometry has been measured in Shwartz et al.[4], we extend these studies to multiple Fourier components and with significantly higher statistics, which allows us to determine the second order nonlinear structure factor. We measure the efficiency, angular dependence, and contributions from different source terms of the process. We find good agreement of our measurements with the quasi-free electron model.

physics.optics↗
arXiv2015

Photoproduction of {\omega} Mesons off the Proton

The differential cross sections and unpolarized spin-density matrix elements for the reaction $\gamma p\to p\omega$ were measured using the CBELSA/TAPS experiment for initial photon energies ranging from the reaction threshold to 2.5 GeV. These observables were measured from the radiative decay of the $\omega$ meson, $\omega\to\pi^0\gamma$. The cross sections cover the full angular range and show the full extent of the $t$-channel forward rise. The overall shape of the angular distributions in the differential cross sections and unpolarized spin-density matrix elements are in fair agreement with previous data. In addition, for the first time, a beam of linearly-polarized tagged photons in the energy range from 1150 MeV to 1650 MeV was used to extract polarized spin-density matrix elements. These data were included in the Bonn-Gatchina partial wave analysis (PWA). The dominant contribution to $\omega$ photoproduction near threshold was found to be the $3/2^+$ partial wave, which is primarily due to the sub-threshold $N(1720)\,3/2^+$ resonance. At higher energies, pomeron-exchange was found to dominate whereas $\pi$-exchange remained small. These $t$-channel contributions as well as further contributions from nucleon resonances were necessary to describe the entire dataset: the $1/2^-$, $3/2^-$, and $5/2^+$ partial waves were also found to contribute significantly.

nucl-ex↗
arXiv2015

High statistics study of the reaction $\gamma p\to p\;2\pi^0$

The photoproduction of 2$\pi^0$ mesons off protons was studied with the Crystal Barrel/TAPS experiment at the electron accelerator ELSA in Bonn. The energy of photons produced in a radiator was tagged in the energy range from 600\,MeV to 2.5\,GeV. Differential and total cross sections and $p\pi^0\pi^0$ Dalitz plots are presented. Part of the data was taken with a diamond radiator producing linearly polarized photons, and beam asymmetries were derived. Properties of nucleon and $\Delta$ resonances contributing to the $p\pi^0\pi^0$ final state were determined within the BnGa partial wave analysis. The data presented here allow us to determine branching ratios of nucleon and $\Delta$ resonances for their decays into $p\pi^0\pi^0$ via several intermediate states. Most prominent are decays proceeding via $\Delta(1232)\pi$, $N(1440)1/2^+\pi$, $N(1520)3/2^-\pi$, $N(1680)5/2^+\pi$, but also $pf_0(500)$, $pf_0(980)$, and $pf_2(1270)$ contribute to the reaction.

nucl-ex↗
arXiv2013

Residual Stresses in Glasses

The history dependence of the glasses formed from flow-melted steady states by a sudden cessation of the shear rate $\dot\gamma$ is studied in colloidal suspensions, by molecular dynamics simulations, and mode-coupling theory. In an ideal glass, stresses relax only partially, leaving behind a finite persistent residual stress. For intermediate times, relaxation curves scale as a function of $\dot\gamma t$, even though no flow is present. The macroscopic stress evolution is connected to a length scale of residual liquefaction displayed by microscopic mean-squared displacements. The theory describes this history dependence of glasses sharing the same thermodynamic state variables, but differing static properties.

cond-mat.soft↗
arXiv2013

Stress-strain relations in bulk metallic glasses and colloidal dispersions

A comparison is made between the nonlinear rheological response of bulk metallic glass formers and of colloidal dispersions. Stress-strain curves measured after switch-on of constant deformation rates are analyzed quantitatively using a schematic model of mode coupling theory generalized to homogeneous and incompressible flows. A mapping between metallic and dispersion rheology is possible when stresses are rescaled by an entropic scale, accumulated strains by geometrical factors, and rates by the intrinsic relaxation time. Exploiting this similarity and the possibility to directly observe individual colloidal particles, we investigate the structural distortions in the colloidal system using confocal microscopy. The distortions exhibit the (from elasticity theory) expected quadrupolar but also a strong isotropic component.

cond-mat.soft↗
arXiv2013

Direct measurement of time-dependent density-density correlations in a solid through the acoustic analog of the dynamical Casimir effect

The macroscopic characteristics of a solid, such as its thermal, optical or transport properties are determined by the available microscopic states above its lowest energy level. These slightly higher quantum states are described by elementary excitations and dictate the response of the system under external stimuli. The spectrum of these excitations, obtained typically from inelastic neutron and x-ray scattering, is the spatial and temporal Fourier transform of the density-density correlation function of the system, which dictates how a perturbation propagates in space and time. As frequency-domain measurements do not generally contain phase information, time-domain measurements of these fluctuations could yield a more direct method for investigating the excitations of solids and their interactions both in equilibrium and far-from equilibrium. Here we show that the diffuse scattering of femtosecond x-ray pulses produced by a free electron laser (FEL) can directly measure these density-density correlations due to lattice vibrations in the time domain. We obtain spectroscopic information of the lattice excitations with unprecedented momentum- and frequency- resolution, without resolving the energy of the outgoing photon. Correlations are created via an acoustic analog of the dynamical Casimir effect, where a femtosecond laser pulse slightly quenches the phonon frequencies, producing pairs of squeezed phonons at momenta +q and -q. These pairs of phonons manifest as macroscopic, time-dependent coherences in the displacement correlations that are then probed directly by x-ray scattering. Since the time-dependent correlations are preferentially created in regions of strong electron-phonon coupling, the time-resolved approach is natural as a spectroscopic tool of low energy collective excitations in solids, and their microscopic interactions, both in linear response and beyond.

cond-mat.mtrl-sci↗
arXiv2012

First-Principles Constitutive Equation for Suspension Rheology

We provide a detailed derivation of a recently developed first-principles approach to calculating averages in systems of interacting, spherical Brownian particles under time-dependent flow. Although we restrict ourselves to flows which are both homogeneous and incompressible, the time-dependence and geometry (e.g. shear, extension) are arbitrary. The approximations formulated within mode-coupling theory are particularly suited to dense colloidal suspensions and capture the slow relaxation arising from particle interactions and the resulting glass transition to an amorphous solid. The delicate interplay between slow structural relaxation and time-dependent external flow in colloidal suspensions may thus be studied within a fully tensorial theory.

cond-mat.soft↗
arXiv2012

Transparency ratio in \gamma A -> \eta' A' and the in-medium \eta' width

The photoproduction of \eta'-mesons off different nuclei has been measured with the CBELSA/TAPS detector system for incident photon energies between 1500 - 2200 MeV. The transparency ratio has been deduced and compared to theoretical calculations describing the propagation of \eta'-mesons in nuclei. The comparison indicates a width of the \eta' -meson of the order of \Gamma= 15-25 MeV at \rho =\rho_0 for an average momentum p_{\eta'} = 1050 MeV/c, at which the \eta'-meson is produced in the nuclear rest frame. The inelastic \eta' N cross section is estimated to be 3 - 10 mb. Parameterizing the photoproduction cross section of \eta'-mesons by \sigma(A) = \sigma_0 A^{\alpha}, a value of \alpha = 0.84\pm0.03 has been deduced.

nucl-ex↗
arXiv2012

Schematic Mode Coupling Theory of Glass Rheology: Single and Double Step Strains

Mode coupling theory (MCT) has had notable successes in addressing the rheology of hard-sphere colloidal glasses, and also soft colloidal glasses such as star-polymers. Here, we explore the properties of a recently developed MCT-based schematic constitutive equation under idealized experimental protocols involving single and then double step strains. We find strong deviations from expectations based on factorable, BKZ-type constitutive models. Specifically, a nonvanishing stress remains long after the application of two equal and opposite step strains; this residual stress is a signature of plastic deformation. We also discuss the distinction between hypothetically instantaneous step strains and fast ramps. These are not generally equivalent in our MCT approach, with the latter more likely to capture the physics of experimental `step' strains. The distinction points to the different role played by reversible anelastic, and irreversible plastic rearrangements.

cond-mat.soft↗