Search arXivSearch

arXiv subjects

S. Colonna

Publications and source records attributed to S. Colonna.

6 recordsLinked to original sources

Atomic structure of the single step and dynamics of Sn adatoms on the Si(111)-\sqrt{3}\times\sqrt{3}-Sn surface

The atomic structure of well-ordered single steps on the Si(111)-\sqrt{3}\times\sqrt{3}-Sn surface and the dynamics of Sn adatoms in the vicinity of these steps was studied. The work was performed using low-temperature scanning tunneling microscopy (STM) and ab initio calculations based on the density-functional theory. The STM tip was used to record the tunneling current versus time on top of oscillating adatoms, keeping the feedback loop turned off. The dynamics of adatoms, detected as the telegraph noise present in the tunneling current, was registered near the steps at 80 K. The atomic structure model of the single steps consisting of Sn atomic chains along the steps was developed. This structure leads to the formation of potential double wells near the steps acting as traps for Sn atoms and explains the fluctuating current recorded in these areas.

cond-mat.mtrl-sci

Morphology and properties evolution upon ring-opening polymerization during extrusion of cyclic butylene terephthalate and graphene-related-materials into thermally conductive nanocomposites

In this work, the study of thermal conductivity before and after in-situ ring-opening polymerization of cyclic butylene terephthalate into poly (butylene terephthalate) in presence of graphene-related materials (GRM) is addressed, to gain insight in the modification of nanocomposites morphology upon polymerization. Five types of GRM were used: one type of graphite nanoplatelets, two different grades of reduced graphene oxide (rGO) and the same rGO grades after thermal annealing for 1 hour at 1700{\deg}C under vacuum to reduce their defectiveness. Polymerization of CBT into pCBT, morphology and nanoparticle organization were investigated by means of differential scanning calorimetry, electron microscopy and rheology. Electrical and thermal properties were investigated by means of volumetric resistivity and bulk thermal conductivity measurement. In particular, the reduction of nanoflake aspect ratio during ring-opening polymerization was found to have a detrimental effect on both electrical and thermal conductivities in nanocomposites.

cond-mat.mtrl-sci

Effect of processing conditions on the thermal and electrical conductivity of poly (butylene terephthalate) nanocomposites prepared via ring-opening polymerization

Successful preparation of polymer nanocomposites, exploiting graphene-related materials, via melt mixing technology requires precise design, optimization and control of processing. In the present work, the effect of different processing parameters during the preparation of poly (butylene terephthalate) nanocomposites, through ring-opening polymerization of cyclic butylene terephthalate in presence of graphite nanoplatelets (GNP), was thoroughly addressed. Processing temperature (240{\deg}C or 260{\deg}C), extrusion time (5 or 10 minutes) and shear rate (50 or 100 rpm) were varied by means of a full factorial design of experiment approach, leading to the preparation of polybutylene terephthalate/GNP nanocomposite in 8 different processing conditions. Morphology and quality of GNP were investigated by means of electron microscopy, X-ray photoelectron spectroscopy, thermogravimetry and Raman spectroscopy. Molecular weight of the polymer matrix in nanocomposites and nanoflake dispersion were experimentally determined as a function of the different processing conditions. The effect of transformation parameters on electrical and thermal properties was studied by means of electrical and thermal conductivity measurement. Heat and charge transport performance evidenced a clear correlation with the dispersion and fragmentation of the GNP nanoflakes; in particular, gentle processing conditions (low shear rate, short mixing time) turned out to be the most favourable condition to obtain high conductivity values.

cond-mat.mtrl-sci

Effect of morphology and defectiveness of graphene-related materials on the electrical and thermal conductivity of their polymer nanocomposites

In this work, electrically and thermally conductive poly (butylene terephthalate) nanocomposites were prepared by in-situ ring-opening polymerization of cyclic butylene terephthalate (CBT) in presence of a tin-based catalyst. One type of graphite nanoplatelets (GNP) and two different grades of reduced graphene oxide (rGO) were used. Furthermore, high temperature annealing treatment under vacuum at 1700{\deg}C was carried out on both RGO to reduce their defectiveness and study the correlation between the electrical/thermal properties of the nanocomposites and the nanoflakes structure/defectiveness. The morphology and quality of the nanomaterials were investigated by means of electron microscopy, x-ray photoelectron spectroscopy, thermogravimetry and Raman spectroscopy. Thermal, mechanical and electrical properties of the nanocomposites were investigated by means of rheology, dynamic mechanical thermal analysis, volumetric resistivity and thermal conductivity measurements. Physical properties of nanocomposites were correlated with the structure and defectiveness of nanoflakes, evidencing a strong dependence of properties on nanoflakes structure and defectiveness. In particular, a significant enhancement of both thermal and electrical conductivities was demonstrated upon the reduction of nanoflakes defectiveness.

cond-mat.mtrl-sci

Effect of thermal annealing on the heat transfer properties of reduced graphite oxide flakes: a nanoscale characterization via scanning thermal microscopy

This paper reports on the thermal properties of reduced graphite oxide (RGO) flakes, studied by means of scanning thermal microscopy (SThM). This technique was demonstrated to allow thermal characterization of the flakes with a spatial resolution of the order of a few tens of nanometers, while recording nanoscale topography at the same time. Several individual RGO flakes were analyzed by SThM, both as obtained after conventional thermal reduction and after a subsequent annealing at 1700{\deg}C. Significant differences in the thermal maps were observed between pristine and annealed flakes, reflecting higher heat dissipation on annealed RGO flakes compared with pristine ones. This result was correlated with the reduction of RGO structure defectiveness. In particular, a substantial reduction of oxidized groups and sp3 carbons upon annealing was proven by X-ray photoelectron and Raman spectroscopies, while the increase of crystalline order was demonstrated by X-ray diffraction, in terms of higher correlation lengths both along and perpendicular to the graphene planes. Results presented in this paper provide experimental evidence for the qualitative correlation between the defectiveness of graphene-related materials and their thermal conductivity, which is clearly crucial for the exploitation of these materials into thermally conductive nanocomposites.

cond-mat.mtrl-sci

First-principles calculations and bias-dependent STM measurements at the alpha-Sn/Ge(111) surface: a clear indication for the 1U2D configuration

The nature of the alpha-Sn/Ge(111) surface is still a matter of debate. In particular, two possible configurations have been proposed for the 3x3 ground state of this surface: one with two Sn adatoms in a lower position with respect to the third one (1U2D) and the other with opposite configuration (2U1D). By means of first-principles quasiparticle calculations we could simulate STM images as a function of bias voltage and compare them with STM experimental results at 78K, obtaining an unambiguous indication that the stable configuration for the alpha-Sn/Ge(111) surface is the 1U2D. The possible inequivalence of the two down Sn adatoms is also discussed.

cond-mat.mtrl-sci