arXiv subjects

Wen Chen

Publications and source records attributed to Wen Chen.

At least 217 records · Page 12Linked to original sources

arXiv2025

Static IRS Meets Distributed MIMO: A New Architecture for Dynamic Beamforming

Intelligent reflecting surface (IRS) has been considered as a revolutionary technology to enhance the wireless communication performance. To cater for multiple mobile users, adjusting IRS beamforming patterns over time, i.e., dynamic IRS beamforming (DIBF), is generally needed for achieving satisfactory performance, which results in high controlling power consumption and overhead. To avoid such cost, we propose a new architecture based on the static regulated IRS for wireless coverage enhancement, where the principle of distributed multiple-input multiple-output (D-MIMO) is integrated into the system to exploite the diversity of spatial directions provided by multiple access points (APs). For this new D-MIMO empowered static IRS architecture, the total target area is partitioned into several subareas and each subarea is served by an assigned AP. We consider to maximize the worst-case received power over all locations in the target area by jointly optimizing a single set of IRS beamforming pattern and AP-subarea association. Then, a two-step algorithm is proposed to obtain its high-quality solution. Theoretical analysis unveils that the fundamental squared power gain can still be achieved over all locations in the target area. The performance gap relative to the DIBF scheme is also analytically quantified. Numerical results validate our theoretical findings and demonstrate the effectiveness of our proposed design over benchmark schemes.

cs.IT↗

arXiv2024

Throughput Maximization for UAV-enabled Integrated Periodic Sensing and Communication

Unmanned aerial vehicle (UAV) is expected to revolutionize the existing integrated sensing and communication (ISAC) system and promise a more flexible joint design. Nevertheless, the existing works on ISAC mainly focus on exploring the performance of both functionalities simultaneously during the entire considered period, which may ignore the practical asymmetric sensing and communication requirements. In particular, always forcing sensing along with communication may make it is harder to balance between these two functionalities due to shared spectrum resources and limited transmit power. To address this issue, we propose a new integrated periodic sensing and communication mechanism for the UAV-enabled ISAC system to provide a more flexible trade-off between two integrated functionalities. Specifically, the system achievable rate is maximized via jointly optimizing UAV trajectory, user association, target sensing selection, and transmit beamforming, while meeting the sensing frequency and beam pattern gain requirement for the given targets. Despite that this problem is highly non-convex and involves closely coupled integer variables, we derive the closed-form optimal beamforming vector to dramatically reduce the complexity of beamforming design, and present a tight lower bound of the achievable rate to facilitate UAV trajectory design. Based on the above results, we propose a penalty-based algorithm to efficiently solve the considered problem. The optimal achievable rate and the optimal UAV location are analyzed under a special case of infinity number of antennas. Furthermore, we prove the structural symmetry between the optimal solutions in different ISAC frames without location constraints and propose an efficient algorithm for solving the problem with location constraints.

cs.IT↗

arXiv2024

Movable Intelligent Surface (MIS) for Wireless Communications: Architecture, Modeling, Algorithm, and Prototyping

Reconfigurable intelligent surfaces enhance wireless systems by reshaping propagation environments. However, dynamic metasurfaces (MSs) with numerous phase-shift elements incur undesired control and hardware costs. In contrast, static MSs (SMSs), configured with static phase shifts pre-designed for specific communication demands, offer a cost-effective alternative by eliminating element-wise tuning. Nevertheless, SMSs typically support a single beam pattern with limited flexibility. In this paper, we propose a novel Movable Intelligent Surface (MIS) technology that enables dynamic beamforming while maintaining static phase shifts. Specifically, we design a MIS architecture comprising two closely stacked transmissive MSs: a larger fixed-position MS 1 and a smaller movable MS 2. By differentially shifting MS 2's position relative to MS 1, the MIS synthesizes distinct beam patterns. Then, we model the interaction between MS 2 and MS 1 using binary selection matrices and padding vectors and formulate a new optimization problem that jointly designs the MIS phase shifts and selects shifting positions for worst-case signal-to-noise ratio maximization. This position selection, equal to beam pattern scheduling, offers a new degree of freedom for RIS-aided systems. To solve the intractable problem, we develop an efficient algorithm that handles unit-modulus and binary constraints and employs manifold optimization methods. Finally, extensive validation results are provided. We implement a MIS prototype and perform proof-of-concept experiments, demonstrating the MIS's ability to synthesize desired beam patterns that achieve one-dimensional beam steering. Numerical results show that by introducing MS 2 with a few elements, MIS effectively offers beamforming flexibility for significantly improved performance. We also draw insights into the optimal MIS configuration and element allocation strategy.

eess.SP↗

arXiv2024

Efficient Joint Precoding Design for Wideband Intelligent Reflecting Surface-Assisted Cell-Free Network

In this paper, we propose an efficient joint precoding design method to maximize the weighted sum-rate in wideband intelligent reflecting surface (IRS)-assisted cell-free networks by jointly optimizing the active beamforming of base stations and the passive beamforming of IRS. Due to employing wideband transmissions, the frequency selectivity of IRSs has to been taken into account, whose response usually follows a Lorentzian-like profile. To address the high-dimensional non-convex optimization problem, we employ a fractional programming approach to decouple the non-convex problem into subproblems for alternating optimization between active and passive beamforming. The active beamforming subproblem is addressed using the consensus alternating direction method of multipliers (CADMM) algorithm, while the passive beamforming subproblem is tackled using the accelerated projection gradient (APG) method and Flecher-Reeves conjugate gradient method (FRCG). Simulation results demonstrate that our proposed approach achieves significant improvements in weighted sum-rate under various performance metrics compared to primal-dual subgradient (PDS) with ideal reflection matrix. This study provides valuable insights for computational complexity reduction and network capacity enhancement.

eess.SP↗

arXiv2024

Distributed Massive MIMO-Aided Task Offloading in Satellite-Terrestrial Integrated Multi-Tier VEC Networks

This paper proposes a distributed massive multiple input multiple-output (DM-MIMO) aided multi-tier vehicular edge computing (VEC) system. In particular, each vehicle terminal (VT) offloads its computational task to the roadside unit (RSU) by orthogonal frequency division multiple access (OFDMA), which can be computed locally at the RSU and offloaded to the central processing unit (CPU) via massive satellite access points (SAPs) for remote computation. By considering the partial task offloading model, we consider the joint optimization of the task offloading, subchannel allocation and precoding optimization to minimize the total cost in terms of total delay and energy consumption. To solve this non-convex problem, we transform the original problem into three sub-problems and use the alternate optimization algorithm to solve it. First, we transform the subcarrier allocation problem of discrete variables into convex optimization problem of continuous variables. Then, we use multiple quadratic transformations and Lagrange multiplier method to transform the non-convex subproblem of optimizing precoding vectors into a convex problem, while the task offloading subproblem is a convex problem. Given the subcarrier and the task allocation and precoding result, we finally find the joint optimized results by iterative optimization algorithm. Simulation results show that our proposed algorithm is superior to other benchmarks.

cs.DC↗

arXiv2024

Space-Time-Modulated Wideband Radiation-Type Programmable Metasurface for Low Sidelobe Beamforming

Programmable metasurfaces promise a great potential to construct low-cost phased array systems due to the capability of elaborate modulation over electromagnetic (EM) waves. However, they are in either reflective or transmissive mode, and usually possess a relatively high profile as a result of the external feed source. Besides, it is difficult to conduct multibit phase shift in metasurfaces, when comparing with conventional phased arrays. Here, we propose a strategy of space-time modulated wideband radiation-type programmable metasurface for low side-lobe beamforming. The wideband programmable metasurface avoids the space-feed external source required by its traditional counterpart, thus achieving a significant reduction of profile through integration of a highefficiency microwave-fed excitation network and metasurface. Furthermore, through introducing space-time-modulated strategy, the high-accuracy amplitude-phase weight algorithm can also be synchronously carried out on the first harmonic component for low side-lobe beam-scanning. Most importantly, adaptive beamforming and generation of interference null can further be created after analyzing the harmonic component characteristics of received signals.

eess.SP↗

arXiv2024

Throughput Maximization for Movable Antenna Systems with Movement Delay Consideration

In this paper, we model the minimum achievable throughput within a transmission block of restricted duration and aim to maximize it in movable antenna (MA)-enabled multiuser downlink communications. Particularly, we account for the antenna moving delay caused by mechanical movement, which has not been fully considered in previous studies, and reveal the trade-off between the delay and signal-to-interference-plus-noise ratio at users. To this end, we first consider a single-user setup to analyze the necessity of antenna movement. By quantizing the virtual angles of arrival, we derive the requisite region size for antenna moving, design the initial MA position, and elucidate the relationship between quantization resolution and moving region size. Furthermore, an efficient algorithm is developed to optimize MA position via successive convex approximation, which is subsequently extended to the general multiuser setup. Numerical results demonstrate that the proposed algorithms outperform fixed-position antenna schemes and existing ones without consideration of movement delay. Additionally, our algorithms exhibit excellent adaptability and stability across various transmission block durations and moving region sizes, and are robust to different antenna moving speeds. This allows the hardware cost of MA-aided systems to be reduced by employing low rotational speed motors.

cs.IT↗

arXiv2024

Dynamic Trajectory and Power Control in Ultra-Dense UAV Networks: A Mean-Field Reinforcement Learning Approach

In ultra-dense unmanned aerial vehicle (UAV) networks, it is challenging to coordinate the resource allocation and interference management among large-scale UAVs, for providing flexible and efficient service coverage to the ground users (GUs). In this paper, we propose a learning-based resource allocation scheme in an ultra-dense UAV communication network, where the GUs' service demands are time-varying with unknown distributions. We formulate the non-cooperative game among multiple co-channel UAVs as a stochastic game, where each UAV jointly optimizes its trajectory, user association, and downlink power control to maximize the expectation of its locally cumulative energy efficiency under the interference and energy constraints. To cope with the scalability issue in a large-scale network, we further formulate the problem as a mean-field game (MFG), which simplifies the interactions among the UAVs into a two-player game between a representative UAV and a mean-field. We prove the existence and uniqueness of the equilibrium for the MFG, and propose a model-free mean-field reinforcement learning algorithm named maximum entropy mean-field deep Q network (ME-MFDQN) to solve the mean-field equilibrium in both fully and partially observable scenarios. The simulation results reveal that the proposed algorithm improves the energy efficiency compared with the benchmark algorithms. Moreover, the performance can be further enhanced if the GUs' service demands exhibit higher temporal correlation or if the UAVs have wider observation capabilities over their nearby GUs.

eess.SY↗

arXiv2024

Beamforming Design and Multi-User Scheduling in Transmissive RIS Enabled Distributed Cooperative ISAC Networks with RSMA

In this paper, we propose a novel transmissive reconfigurable intelligent surface (TRIS) transceiver-empowered distributed cooperative integrated sensing and communication (ISAC) network to enhance coverage as well as to enhance wireless environment understanding. Based on the network requirements, the users are categorized into cooperative users (CUEs) and destination users (DUEs), and the CUEs utilize their own resources to serve the DUEs. To realize cooperation, we implement rate-splitting multiple access (RSMA) at the base station (BS), where the common stream is decoded and reencoded at the CUEs and forwarded to the DUEs, while the private stream satisfies the CUEs' own communication requirements. We construct an optimization problem with maximum minimum radar mutual information (RMI) as the objective function to optimize the BS beamforming matrix, the CUE beamforming matrices, the common stream rate vectors, and the user scheduling vectors. Due to the coupling of the optimization variables and non-convex operation, the proposed problem is a non-convex optimization problem that cannot be solved directly. To address the above challenges, we adopt a consensus alternating direction method of multipliers (ADMM) framework to decouple the optimization variables and solve it. Specifically, the problem is decoupled into multiple subproblems and solved by iterative optimization independently until overall convergence is achieved. Finally, numerical results validate the superiority of the proposed scheme in terms of improving communication sum-rate and RMI, and greatly reduce the algorithm complexity.

cs.IT↗

arXiv2024

IREE Oriented Active RIS-Assisted Green communication System with Outdated CSI

The rapid evolution of communication technologies has spurred a growing demand for energy-efficient network architectures and performance metrics. Active Reconfigurable Intelligent Surfaces (RIS) are emerging as a key component in green network architectures. Compared to passive RIS, active RIS are equipped with amplifiers on each reflecting element, allowing them to simultaneously reflect and amplify signals, thereby overcoming the double multiplicative fading in the phase response, and improving both system coverage and performance. Additionally, the Integrated Relative Energy Efficiency (IREE) metric, as introduced in [1], addresses the dynamic variations in traffic and capacity over time and space, enabling more energy-efficient wireless systems. Building on these advancements, this paper investigates the problem of maximizing IREE in active RIS-assisted green communication systems. However, acquiring perfect Channel State Information (CSI) in practical systems poses significant challenges and costs. To address this, we derive the average achievable rate based on outdated CSI and formulated the corresponding IREE maximization problem, which is solved by jointly optimizing beamforming at both the base station and RIS. Given the non-convex nature of the problem, we propose an Alternating Optimization Successive Approximation (AOSO) algorithm. By applying quadratic transform and relaxation techniques, we simplify the original problem and alternately optimize the beamforming matrices at the base station and RIS. Furthermore, to handle the discrete constraints of the RIS reflection coefficients, we develop a successive approximation method. Experimental results validate our theoretical analysis of the algorithm's convergence , demonstrating the effectiveness of the proposed algorithm and highlighting the superiority of IREE in enhancing the performance of green communication networks.

eess.SP↗

arXiv2024

Model Predictive Control Enabled UAV Trajectory Optimization and Secure Resource Allocation

In this paper, we investigate a secure communication architecture based on unmanned aerial vehicle (UAV), which enhances the security performance of the communication system through UAV trajectory optimization. We formulate a control problem of minimizing the UAV flight path and power consumption while maximizing secure communication rate over infinite horizon by jointly optimizing UAV trajectory, transmit beamforming vector, and artificial noise (AN) vector. Given the non-uniqueness of optimization objective and significant coupling of the optimization variables, the problem is a non-convex optimization problem which is difficult to solve directly. To address this complex issue, an alternating-iteration technique is employed to decouple the optimization variables. Specifically, the problem is divided into three subproblems, i.e., UAV trajectory, transmit beamforming vector, and AN vector, which are solved alternately. Additionally, considering the susceptibility of UAV trajectory to disturbances, the model predictive control (MPC) approach is applied to obtain UAV trajectory and enhance the system robustness. Numerical results demonstrate the superiority of the proposed optimization algorithm in maintaining accurate UAV trajectory and high secure communication rate compared with other benchmark schemes.

eess.SP↗

arXiv2024

Digital Twin-Assisted Federated Learning with Blockchain in Multi-tier Computing Systems

In Industry 4.0 systems, a considerable number of resource-constrained Industrial Internet of Things (IIoT) devices engage in frequent data interactions due to the necessity for model training, which gives rise to concerns pertaining to security and privacy. In order to address these challenges, this paper considers a digital twin (DT) and blockchain-assisted federated learning (FL) scheme. To facilitate the FL process, we initially employ fog devices with abundant computational capabilities to generate DT for resource-constrained edge devices, thereby aiding them in local training. Subsequently, we formulate an FL delay minimization problem for FL, which considers both of model transmission time and synchronization time, also incorporates cooperative jamming to ensure secure synchronization of DT. To address this non-convex optimization problem, we propose a decomposition algorithm. In particular, we introduce upper limits on the local device training delay and the effects of aggregation jamming as auxiliary variables, thereby transforming the problem into a convex optimization problem that can be decomposed for independent solution. Finally, a blockchain verification mechanism is employed to guarantee the integrity of the model uploading throughout the FL process and the identities of the participants. The final global model is obtained from the verified local and global models within the blockchain through the application of deep learning techniques. The efficacy of our proposed cooperative interference-based FL process has been verified through numerical analysis, which demonstrates that the integrated DT blockchain-assisted FL scheme significantly outperforms the benchmark schemes in terms of execution time, block optimization, and accuracy.

cs.CR↗

arXiv2024

Adversarial Federated Consensus Learning for Surface Defect Classification Under Data Heterogeneity in IIoT

The challenge of data scarcity hinders the application of deep learning in industrial surface defect classification (SDC), as it's difficult to collect and centralize sufficient training data from various entities in Industrial Internet of Things (IIoT) due to privacy concerns. Federated learning (FL) provides a solution by enabling collaborative global model training across clients while maintaining privacy. However, performance may suffer due to data heterogeneity-discrepancies in data distributions among clients. In this paper, we propose a novel personalized FL (PFL) approach, named Adversarial Federated Consensus Learning (AFedCL), for the challenge of data heterogeneity across different clients in SDC. First, we develop a dynamic consensus construction strategy to mitigate the performance degradation caused by data heterogeneity. Through adversarial training, local models from different clients utilize the global model as a bridge to achieve distribution alignment, alleviating the problem of global knowledge forgetting. Complementing this strategy, we propose a consensus-aware aggregation mechanism. It assigns aggregation weights to different clients based on their efficacy in global knowledge learning, thereby enhancing the global model's generalization capabilities. Finally, we design an adaptive feature fusion module to further enhance global knowledge utilization efficiency. Personalized fusion weights are gradually adjusted for each client to optimally balance global and local features. Compared with state-of-the-art FL methods like FedALA, the proposed AFedCL method achieves an accuracy increase of up to 5.67% on three SDC datasets.

cs.LG↗

arXiv2024

Discrete RIS Enhanced Space Shift Keying MIMO System via Reflecting Beamforming Optimization

In this paper, a discrete reconfigurable intelligent surface (RIS)-assisted spatial shift keying (SSK) multiple-input multiple-output (MIMO) scheme is investigated, in which a direct link between the transmitter and the receiver is considered. To improve the reliability of the RIS-SSK-MIMO scheme, we formulate an objective function based on minimizing the average bit error probability (ABEP). Since the reflecting phase shift of RIS is discrete, it is difficult to address this problem directly. To this end, we optimize the RIS phase shift to maximize the Euclidean distance between the minimum constellations by applying the successive convex approximation (SCA) and penaltyalternating optimization method. Simulation results verify the superiority of the proposed RIS-SSK-MIMO scheme and demonstrate the impact of the number of RIS elements, the number of phase quantization bits, and the number of receive and transmit antennas in terms of reliability.

cs.IT↗

arXiv2024

V2X-Assisted Distributed Computing and Control Framework for Connected and Automated Vehicles under Ramp Merging Scenario

This paper investigates distributed computing and cooperative control of connected and automated vehicles (CAVs) in ramp merging scenario under transportation cyber-physical system. Firstly, a centralized cooperative trajectory planning problem is formulated subject to the safely constraints and traffic performance in ramp merging scenario, where the trajectories of all vehicles are jointly optimized. To get rid of the reliance on a central controller and reduce computation time, a distributed solution to this problem implemented among CAVs through Vehicles-to-Everything (V2X) communication is proposed. Unlike existing method, our method can distribute the computational task among CAVs and carry out parallel solving through V2X communication. Then, a multi-vehicles model predictive control (MPC) problem aimed at maximizing system stability and minimizing control input is formulated based on the solution of the first problem subject to strict safety constants and input limits. Due to these complex constraints, this problem becomes high-dimensional, centralized, and non-convex. To solve it in a short time, a decomposition and convex reformulation method, namely distributed cooperative iterative model predictive control (DCIMPC), is proposed. This method leverages the communication capability of CAVs to decompose the problem, making full use of the computational resources on vehicles to achieve fast solutions and distributed control. The two above problems with their corresponding solving methods form the systemic framework of the V2X assisted distributed computing and control. Simulations have been conducted to evaluate the framework's convergence, safety, and solving speed. Additionally, extra experiments are conducted to validate the performance of DCIMPC. The results show that our method can greatly improve computation speed without sacrificing system performance.

eess.SY↗

arXiv2024

Graph-GIC: A Smart and Parallelized Geomagnetically Induced Current Modelling Algorithm Based on Graph Theory for Space Weather Applications

Geomagnetically Induced Current (GIC) refers to the electromagnetic response of the Earth and its conductive modern infrastructures to space weather and would pose a significant threat to high-voltage power grids designed for the alternative current operation. To assess the impact of space weather on the power grid, one needs to calculate the GIC on a national or continental scale. In this study, we developed a smart and parallelized GIC modelling algorithm, Graph GIC. This algorithm deploys a graph representing a power grid in a single-line diagram, in which substations/transformers act as nodes and transmission lines as edges. With these denotations, a power grid and its electric parameters are mathematically represented with an adjacency matrix and an admittance matrix. We used sparse matrix and parallelisation techniques to expedite the intensive computation in cases of large-scale power grids. The Graph GIC was validated with a benchmark grid, applied to the GIC calculation of the 500 kV power grid of Guangdong, China, and conducted preliminary analysis on the grid's susceptibility to geomagnetic storms. The Graph GIC algorithm has the advantage of an intuitive and highly scalable graph representation of a power grid at any scale. It achieves high-accuracy calculation and a speedup of about 18 times after parallelisation. This algorithm could be applied to assess the impact of space weather on a power grid up to continental scales and could be incorporated into global space weather modelling frameworks.

physics.space-ph↗

arXiv2024

Intelligent Reflecting Surface Aided MIMO Networks: Distributed or Centralized Architecture?

We investigate the capacity of a broadcast channel with a multi-antenna base station (BS) sending independent messages to multiple users, aided by IRSs with N elements. In particular, both the distributed and centralized IRS deployment architectures are considered. Regarding the distributed IRS, the N IRS elements form multiple IRSs and each of them is installed near a user cluster; while for the centralized IRS, all IRS elements are located in the vicinity of the BS. To draw essential insights, we first derive the maximum capacity achieved by the distributed IRS and centralized IRS, respectively, under the assumption of line-of-sight propagation and homogeneous channel setups. By capturing the fundamental tradeoff between the spatial multiplexing gain and passive beamforming gain, we rigourously prove that the capacity of the distributed IRS is higher than that of the centralized IRS provided that the total number of IRS elements is above a threshold. Motivated by the superiority of the distributed IRS, we then focus on the transmission and element allocation design under the distributed IRS. By exploiting the user channel correlation of intra-clusters and inter-clusters, an efficient hybrid multiple access scheme relying on both spatial and time domains is proposed to fully exploit both the passive beamforming gain and spatial DoF. Moreover, the IRS element allocation problem is investigated for the objectives of sum-rate maximization and minimum user rate maximization, respectively. Finally, extensive numerical results are provided to validate our theoretical finding and also to unveil the effectiveness of the distributed IRS for improving the system capacity under various system setups.

cs.IT↗

arXiv2024

Ground calibration and network of the first CATCH pathfinder

The Chasing All Transients Constellation Hunters (CATCH) space mission is focused on exploring the dynamic universe via X-ray follow-up observations of various transients. The first pathfinder of the CATCH mission, CATCH-1, was launched on June 22, 2024, alongside the Space-based multiband astronomical Variable Objects Monitor (SVOM) mission. CATCH-1 is equipped with narrow-field optimized Micro Pore Optics (MPOs) featuring a large effective area and incorporates four Silicon Drift Detectors (SDDs) in its focal plane. This paper presents the system calibration results conducted before the satellite integration. Utilizing the data on the performance of the mirror and detectors obtained through the system calibration, combined with simulated data, the ground calibration database can be established. Measuring the relative positions of the mirror and detector system, which were adjusted during system calibration, allows for accurate installation of the entire satellite. Furthermore, the paper outlines the operational workflow of the ground network post-satellite launch.

astro-ph.IM↗