arXiv subjects

Xingbang Yang

Publications and source records attributed to Xingbang Yang.

5 recordsLinked to original sources

arXiv2026

A Reconfigurable Bidirectional Cable-Driven Hip Exoskeleton with Swappable Bench/Backpack Dual-configuration Actuation

Hip exoskeletons provide an important hardware basis for lower-limb rehabilitation and locomotor assistance. Laboratory rehabilitation assessment and system development require substantial actuation and computing resources, whereas mobile assistance requires untethered portability. Integrating both capabilities within one reusable platform remains a central design challenge. This paper presents a reconfigurable bidirectional cable-driven hip exoskeleton platform that rapidly switches between bench-mounted and backpack-mounted actuation while sharing one cable-free wearable hip interface. The platform modularly adapts the actuation configuration, end-effector sensing path, and low-level control interface. Each cable-driven end-effector weighs 0.405 kg, excluding the cable and actuation unit, and integrates an encoder and a torque sensor; experiments validated bench-mounted admittance-based motion tracking capability and backpack-mounted open-loop torque tracking. Human-worn experiments with three healthy participants used myoMOTION to evaluate the platform's wearable-side hip-motion sensing capability, verified bench-to-backpack and backpack-to-bench motion-ready switching across 30 trials in $30.1\pm16.3$ s, and formed a small-scale multimodal wearable-exoskeleton gait dataset for sensing validation and data-driven algorithm development, comprising 8 min bench-mounted treadmill records and 11 min backpack-mounted outdoor walking records. These results show that, by unifying the wearable structure, actuation interface, and sensing path, the proposed platform enables validation of the same hip exoskeleton in both bench-mounted and backpack-mounted configurations, providing reusable hardware for iterative development and applications across scenarios.

cs.RO↗

arXiv2026

Design and Control of a Cable-Driven Switchable Actuator with Torque/Tension Dual Modes for Exoskeletons

Existing wearable exoskeleton architectures are typically constrained by a single mechanical output modality, providing either joint torque around an anatomical joint or linear traction along a limb-training-oriented direction, which limits adaptability to diverse training scenarios. This letter presents a cable-driven switchable actuator (CDSA) that can rapidly switch between torque and tension modes while centralizing all sensing and actuation components at the proximal drive unit. A Coupled Movable Pulley Mechanism (CMPM) provides tension amplification at the distal end-effector, while a bidirectional Cable-Driven Ratchet Mechanism (CDRM) enables mode switching and preload regulation. To eliminate the need for distal instrumentation, multi-source proximal sensors are integrated with a data-driven fusion model to estimate distal output forces. An adaptive dual-mode force control strategy based on iterative learning control (ILC) is further developed. Platform experiments demonstrate transmission efficiencies of $(92.4 \pm 2.0)\%$ and $(96.5 \pm 3.3)\%$ in the torque and tension modes, respectively, along with a tension amplification ratio of $2.77 \pm 0.10$ under tension mode. Tracking tests on simulated knee-joint gait trajectories and short-stroke tension profiles yield stable control, with RMSEs of $(4.52 \pm 0.51)\%$ and $(3.15 \pm 0.19)\%$ of the uncontrolled peak value, respectively. Finally, seated human-coupled experiments validate the system's controllable force generation in both joint-torque and linear-traction application modes.

cs.RO↗

arXiv2026

Optimization Design and Simulation Validation of a Variable Stiffness Actuator Based on a Crossed Four-Bar Mechanism

This paper presents a bio-inspired antagonistic variable stiffness actuator (VSA) based on two crossed four-bar compliant transmission elastic units (CFB-CTEs). The design addresses the difficulty of combining nonlinear elastic shaping with low structural inertia in antagonistic VSA mechanisms. Inspired by the crossed constraint behavior of the anterior and posterior cruciate ligaments during knee flexion, the proposed actuator uses geometric transmission, elastic energy storage, and bilateral antagonistic arrangement to shape the output torque and equivalent stiffness. A multi-objective optimization model is established to balance torque tracking accuracy, equivalent inertia, and mass. The selected compromise design achieved a torque root-mean-square error (RMSE) of $0.883~\mathrm{N\,mm}$ and a total mass of $50.2~\mathrm{g}$. Its average equivalent inertia was reduced by about 78% compared with an independent torque-only optimized design. An ADAMS multibody model was further built to verify the structural response under single-input, opposite-input, and same-input conditions. The results support the feasibility of the proposed crossed four-bar elastic unit as a lightweight nonlinear elastic branch for antagonistic VSAs.

eess.SY↗

arXiv2025

Human Locomotion Implicit Modeling Based Real-Time Gait Phase Estimation

Gait phase estimation based on inertial measurement unit (IMU) signals facilitates precise adaptation of exoskeletons to individual gait variations. However, challenges remain in achieving high accuracy and robustness, particularly during periods of terrain changes. To address this, we develop a gait phase estimation neural network based on implicit modeling of human locomotion, which combines temporal convolution for feature extraction with transformer layers for multi-channel information fusion. A channel-wise masked reconstruction pre-training strategy is proposed, which first treats gait phase state vectors and IMU signals as joint observations of human locomotion, thus enhancing model generalization. Experimental results demonstrate that the proposed method outperforms existing baseline approaches, achieving a gait phase RMSE of $2.729 \pm 1.071%$ and phase rate MAE of $0.037 \pm 0.016%$ under stable terrain conditions with a look-back window of 2 seconds, and a phase RMSE of $3.215 \pm 1.303%$ and rate MAE of $0.050 \pm 0.023%$ under terrain transitions. Hardware validation on a hip exoskeleton further confirms that the algorithm can reliably identify gait cycles and key events, adapting to various continuous motion scenarios. This research paves the way for more intelligent and adaptive exoskeleton systems, enabling safer and more efficient human-robot interaction across diverse real-world environments.

cs.RO↗

arXiv2024

MLP Based Continuous Gait Recognition of a Powered Ankle Prosthesis with Serial Elastic Actuator

Powered ankle prostheses effectively assist people with lower limb amputation to perform daily activities. High performance prostheses with adjustable compliance and capability to predict and implement amputee's intent are crucial for them to be comparable to or better than a real limb. However, current designs fail to provide simple yet effective compliance of the joint with full potential of modification, and lack accurate gait prediction method in real time. This paper proposes an innovative design of powered ankle prosthesis with serial elastic actuator (SEA), and puts forward a MLP based gait recognition method that can accurately and continuously predict more gait parameters for motion sensing and control. The prosthesis mimics biological joint with similar weight, torque, and power which can assist walking of up to 4 m/s. A new design of planar torsional spring is proposed for the SEA, which has better stiffness, endurance, and potential of modification than current designs. The gait recognition system simultaneously generates locomotive speed, gait phase, ankle angle and angular velocity only utilizing signals of single IMU, holding advantage in continuity, adaptability for speed range, accuracy, and capability of multi-functions.

cs.RO↗