Search arXiv⌕ Search
Home/Archive/arXiv

arXiv · 1903.08574

Cooling rate effect on thermoremanent magnetization in archaeological baked clays: an experimental study on modern bricks

Gwenaël Hervé·Annick Chauvin·Philippe Lanos·Pierre Rochette·Mireille Perrin·Michel Perron d'arc
View original source ↗Read source document ↗Export metadata ↓

Abstract

The influence of cooling rate on the intensity of thermoremanent magnetization (TRM) and the necessity to correct archaeo/palaeointensities for this effect have long been recognized. However the reliability of the correction is still questioned. We studied 35 bricks baked in two modern kilns (SK and BK) in known experimental conditions and with measurements of the direction and intensity of the geomagnetic field at the site. The smallest kiln (SK, 0.2 m 3) cooled in around 12 hours and the biggest kiln (BK, 8 m 3) in around 40 hours. Thermomagnetic, hysteresis and backfield curves indicated that the main magnetic carriers were Ti-poor titanomagnetites and Tipoortitanohematites. The fraction of the TRM carried by Ti-poor titanohematites is the maindifference between the two sets of bricks. This fraction is around 5-10% in bricks from BK kilnand up to 40% in those from SK kiln. Intensities of the Earth's magnetic field were determinedusing the original Thellier-Thellier protocol with correction of TRM anisotropy. The averageintensities overestimate the expected field intensity by 5% (SK) and 6% (BK). This resultemphasizes the necessity of the cooling rate correction. In order to have a detailed evaluation ofthe cooling rate effect, we used several slow cooling rates: 0.8, 0.4, 0.2 and 0.1{\textdegree}C/min. Thecorrection factors obtained with the 0.8{\textdegree}C/min cooling ranged between -2% and 21% and wereproportional to the TRM fraction carried by Ti-poor titanohematite. The higher proportion ofthese grains in bricks from SK kiln led to an overestimate of the correction factor and anunderestimate of the intensity by 7%. However, the expected intensity is recovered whentemperature steps higher than 580{\textdegree}C (i.e. in the range of Ti-poor titanohematites unblockingtemperatures) were excluded from the calculation of archaeointensity and cooling rate correction.In the case of the BK kiln bricks, for which Ti-poor titanohematites does not contributesignificantly to the TRM, all tested cooling rates give average intensities close to the expectedvalue. Incorrectly estimating the duration of the archaeological cooling has therefore a lowimpact on the accuracy of the archaeointensity data on these kinds of material.

Explore related subjects

cond-mat.mtrl-sciphysics.geo-ph

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Gwenaël Hervé, Annick Chauvin, Philippe Lanos, Pierre Rochette, Mireille Perrin, Michel Perron d'arc. 2019-03-18. Cooling rate effect on thermoremanent magnetization in archaeological baked clays: an experimental study on modern bricks. https://doi.org/10.1093/gji%2Fggz076

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related papers

arXiv2026

Structure and dynamics of the negative thermal expansion material Cd(CN)$_2$ under hydrostatic pressure

We use a combination of variable-temperature / variable-pressure neutron powder diffraction, variable-pressure inelastic neutron scattering, and quantum chemical calculations to interrogate the behaviour of the negative thermal expansion (NTE) material $^{114}$Cd(CN)$_2$ under hydrostatic pressure. We determine the equation of state of the ambient-pressure phase, and discover the so-called `warm hardening' effect whereby the material becomes elastically stiffer as it is heated. We also identify a number of high-pressure phases, and map out the phase behaviour of Cd(CN)$_2$ over the range $0\leq p\leq0.5$\,GPa, $100\leq T\leq300$\,K. As expected for an NTE material, the low-energy phonon frequencies are found to soften under pressure, and we determine an effective Gr{ü}neisen parameter for these modes. Finally, we show that the elastic behaviour of Cd(CN)$_2$ is sensitive to the local Cd coordination environment, which suggests an interplay between short- (phononic) and long-timescale (cyanide flips) fluctuations in Cd(CN)$_2$.

cond-mat.mtrl-sci↗
arXiv2026

Unconventional Magnetism, Sliding Ferroelectricity, and Magneto-Optical Kerr Effect in Multiferroic Bilayers

Antiferromagnetic (AFM) materials provide a platform to couple altermagnetic (AM) spin-splitting with the magneto-optical Kerr effect (MOKE), offering potential for next-generation quantum technologies. In this work, first-principles calculations, symmetry analysis, and kp modeling are employed to show that interlayer sliding in AFM multiferroic bilayers enables control of electronic, magnetic, and magneto-optical properties. This study reveals an intriguing dimension-driven AM crossover: the 2D paraelectric (PE) bilayer exhibits spin-degenerate bands protected by the [C2||Mc] spin-space symmetry, whereas the 3D counterpart manifests AM spin-splitting along kz \neq 0 paths. Furthermore, interlayer sliding breaks this Mc symmetry and stabilizes a ferroelectric (FE) state with compensated ferrimagnetism, where the Zeeman-like field is responsible for the nonrelativistic spin-splitting. In the FE phase, spin-orbit coupling (SOC) lifts accidental degeneracies and produces `alternating' spin-polarized bands through the interplay of Zeeman and Rashba effects. Crucially, spin polarization, ferrovalley polarization, and the Kerr angle can all be reversed by switching either sliding ferroelectricity or the Neel vector. Our findings reveal the rich coupling among electronic, magnetic, and optical orders in sliding multiferroics, illustrating new prospects for ultralow-power spintronic and optoelectronic devices.

cond-mat.mtrl-sci↗
arXiv2026

Lead-free piezoelectric perovskites for arterial-pulse e-skin: from configurational complexity to equivariant machine-learning potentials

Continuous, non-invasive monitoring of the arterial pulse is a clinical priority for cardiovascular disease, the leading cause of global mortality. Flexible piezoelectric electronic skins can transduce the 1-10 kPa pressure wave into a self-powered voltage, but the best-performing piezoceramics are lead-based, and their toxicity is incompatible with skin contact and with tightening RoHS/REACH regulation. Among lead-free alternatives, the BaTiO$3$-based solid solution BZT-BCT reaches $d{33} \approx 620$ pC/N near its tricritical morphotropic phase boundary, rivalling soft PZT while remaining biocompatible. Exploiting this in a wearable confronts a sensitivity-flexibility paradox and three computational walls: the combinatorial explosion of atomic configurations in a disordered solid solution, the band-gap error of affordable density-functional approximations, which corrupts leakage and insulation estimates, and the 0 K nature of standard calculations against a 310 K operating temperature. We review lead-free piezoelectrics, morphotropic-boundary physics and fabricated flexible devices, then argue that equivariant machine-learning interatomic potentials --- coupled to a tiered functional hierarchy and finite-temperature lattice dynamics --- can survey the full configurational ensemble at body temperature and close the gap to a clinically viable lead-free pulse sensor.

cond-mat.mtrl-sci↗