Search arXiv⌕ Search

arXiv subjects

Gabriele Giacomini

Publications and source records attributed to Gabriele Giacomini.

At least 19 recordsLinked to original sources

Test beam results for machine-learning-based reconstruction of resistive silicon sensors

The advent of Low-Gain Avalanche Diodes (LGADs) and AC-coupled Low-Gain Avalanche Diodes (AC-LGADs) as candidate technologies for four-dimensional tracking has moved part of the reconstruction burden onto the analog waveforms of the sensor, in which the charge shared between electrodes encodes the impact position well below the electrode pitch. Recovering that position is a continuous, non-linear inverse problem. Transient Current Technique measurements characterize this problem at fixed injected charge and high signal-to-noise, whereas a minimum-ionizing beam adds Landau fluctuations in the deposited charge under detector operating conditions. We report test beam results for full-waveform reconstruction of an AC-LGAD of 500 $μ$m pitch read out on a $2\times2$ pad matrix, exposed to the 120 GeV pion beam of the CERN Super Proton Synchrotron (SPS) and read out alongside a six-plane MIMOSA-26 telescope. The telescope is aligned, and its per-plane resolutions are calibrated in situ, giving a track pointing resolution of about 2.5 $μ$m per axis at the device, so that the measured residual is the sensor response rather than a convolution with the reference. We then compare two analytic estimators, the parameter-free charge-imbalance formula and a fitted linear matrix inversion, with the topology-agnostic transformer developed for resistive silicon sensors. Over the full active pad, the transformer reaches a median total position with up to factor 3 improvement. Within the charge-sharing core, the three methods converge to the floor of this sensor at the achieved signal-to-noise.

physics.ins-det↗

Ultra-Fast 4H-SiC AC-LGAD for 4D Tracking Applications

4H-SiC low gain avalanche detectors (LGADs) combine internal gain with the high carrier saturation drift velocity, thermal stability, and low leakage current of SiC. AC-coupled readout (AC-LGAD) adds position information to the precise timing, which enables 4D tracking. This work reports the first experimental demonstration of a 4H-SiC AC-LGAD. Devices with a $1.0\times1.0$~mm$^2$ active area and a $2\times2$ array of AC-coupled pads at a pitch of 500~$μ$m were fabricated with two gain-layer doping concentrations, $4\times10^{17}$ and $5\times10^{17}$~cm$^{-3}$, and characterized with a 375~nm ultraviolet transient current technique (UV-TCT) scanning setup. The hit position and time were reconstructed with the conventional discretized positioning circuit (DPC) and constant fraction discrimination (CFD) methods. They were also reconstructed with a transformer-based neural network, which processes the full waveforms of the four pads through a shared encoder and formulates timing as a per-sample segmentation task. With DPC and CFD, the best position and time resolutions are about 10~$μ$m and 20~ps. The neural network mitigates the nonlinear distortions near the device edges and improves the position resolution to below 5~$μ$m and the time resolution to about 15~ps, improvements of more than 60\% and 30\%, respectively. The higher-doped device reaches a high signal-to-noise ratio at lower bias and keeps good performance at low laser intensities. These results demonstrate the potential of 4H-SiC AC-LGADs for 4D tracking in future collider experiments.

physics.ins-det↗

Impact of Gain Layer Doping Concentration on the Performance of 4H-SiC LGADs

Gain layer doping concentration determines the electric field profile in a low gain avalanche detector (LGAD) and is therefore the primary design parameter. This work reports its influence on the charge collection and timing behavior of 4H-SiC LGADs. Two mesa-isolated devices with cold He ion implanted termination differ only in gain layer doping, $4\times10^{17}$~$cm^{-3}$ and $5\times10^{17}$~$cm^{-3}$, and are characterized together with a PIN diode from the same wafer using the ultraviolet transient current technique (UV-TCT). The 25\% doping difference produces a gain difference of about two orders of magnitude at the same applied bias, representing a gain range of 3.7 to 216. Under UV-TCT excitation, the higher-doped device exhibits time-resolution minima within a gain range of about 20--80 across the investigated laser intensities, consistent with the transition from electronic-noise-dominated jitter to multiplication shot noise. The non-monotonic timing response is also observed under a $^{90}Sr$ beta source with a Si LGAD reference: the higher-doped device reaches 51.7 ps at 280 V and then degrades, while the lower-doped device requires more than 450 V. This measured gain window provides an experimental reference for further optimization of the gain-layer design.

physics.ins-det↗

Impact of Environmental Stress on Low Gain Avalanche Diode Sensors Response

Low Gain Avalanche Diodes or LGADs are silicon sensors capable of achieving excellent timing resolution due to their characteristic internal gain. Detectors based on LGAD technology play a crucial role in High Energy and Nuclear Physics experiments, among other applications. However, their performance is affected by environmental factors such as temperature, humidity, and storage conditions. A systematic evaluation of the response of LGAD sensors as a function of these environmental parameters is therefore of essential importance for any application. LGAD sensors fabricated at the Brookhaven National Laboratory are characterized and stress-tested against various operating conditions, such as rapid temperature and humidity changes. Dedicated and detailed simulations are used to interpret the experimental results.

physics.ins-det↗

Machine Learning-Based Reconstruction for Resistive Silicon Sensors

Low-Gain Avalanche Diodes (LGADs) and AC-coupled Low-Gain Avalanche Diodes (AC-LGADs) are promising technologies for precision timing and four-dimensional tracking. In AC-LGADs, the AC pad is coupled to the resistive n$^{+}$ layer through a dielectric layer, while the gain layer remains unsegmented. This structure provides a 100\% fill factor and enables good spatial resolution with a relaxed readout pitch. The same signal-sharing mechanism that makes interpolation possible complicates the readout: charge spreads across multiple pads, the useful information can approach the electronic-noise threshold, and matrix-inversion approaches can become computationally challenging and sensitive to off-diagonal noise. In this work, we study machine-learning-based reconstruction and compression for resistive silicon sensors. We use full-waveform information from correlated pads to regularise the reconstruction and extract spatial information beyond what is available from binary readouts or reduced-amplitude summaries. We first introduce recurrent neural network models based on LSTM layers, which provide a proof-of-concept implementation for full-waveform reconstruction and have been tested for FPGA deployment using \hls. We also study routes towards bandwidth reduction with waveform rasterisation and window-selection methods, and extend the approach beyond the first model to topology-agnostic transformer-based architectures that use pad coordinates as part of the input. These models are designed to support arbitrary pad counts and geometries, mitigate edge distortions, preserve approximately $10~μ\mathrm{m}$ position resolution for $500~μ\mathrm{m}\times500~μ\mathrm{m}$ pitched sensors, and guide future resistive-silicon sensor designs

hep-ex↗

Response of AC-coupled Low Gain Avalanche Detectors to Ionizing and Non-ionizing Radiation Damage

Low gain avalanche diodes with DC- and AC-coupled readout were exposed to ionizing and non-ionizing radiation at levels relevant to future experiments in particle, nuclear, and medical physics and to astrophysics. Damage-related change in their acceptor removal constants and in the resistivity of the region between the guard ring and the active area are reported, as is change in the leakage current and depletion voltages of the active volumes.

physics.ins-det↗

Gain characterization of LGAD sensors with beta particles and 28-MeV protons

Low Gain Avalanche Diodes, also known as LGADs, are widely considered for fast-timing applications in high energy physics, nuclear physics, space science, medical imaging, and precision measurements of rare processes. Such devices are silicon-based and feature an intrinsic gain due to a $p{^+}$-doped layer that allows the production of a controlled avalanche of carriers, with multiplication on the order of 10-100. This technology can provide time resolution on the order of 20-30 ps, and variants of this technology can provide precision tracking too. The characterization of LGAD performance has so far primarily been focused on the interaction of minimum ionizing particles for high energy and nuclear physics applications. This article expands the study of LGAD performance to highly-ionizing particles, such as 28-MeV protons, which are relevant for several future scientific applications, e.g. in biology and medical physics, among others. These studies were performed with a beam of 28-MeV protons from a tandem Van de Graaff accelerator at Brookhaven National Laboratory and beta particles from a $^{90}{\rm Sr}$ source; these were used to characterize the response and the gain of an LGAD as a function of bias voltage and collected charge. The experimental results are also compared to TCAD simulations.

physics.ins-det↗

Results for pixel and strip centimeter-scale AC-LGAD sensors with a 120 GeV proton beam

We present the results of an extensive evaluation of strip and pixel AC-LGAD sensors tested with a 120 GeV proton beam, focusing on the influence of design parameters on the sensor temporal and spatial resolutions. Results show that reducing the thickness of pixel sensors significantly enhances their time resolution, with 20 $μ$m-thick sensors achieving around 20 ps. Uniform performance is attainable with optimized sheet resistance, making these sensors ideal for future timing detectors. Conversely, 20 $μ$m-thick strip sensors exhibit higher jitter than similar pixel sensors, negatively impacting time resolution, despite reduced Landau fluctuations with respect to the 50 $μ$m-thick versions. Additionally, it is observed that a low resistivity in strip sensors limits signal size and time resolution, whereas higher resistivity improves performance. This study highlights the importance of tuning the n$^{+}$ sheet resistance and suggests that further improvements should target specific applications like the Electron-Ion Collider or other future collider experiments. In addition, the detailed performance of four AC-LGADs sensor designs is reported as examples of possible candidates for specific detector applications. These advancements position AC-LGADs as promising candidates for future 4D tracking systems, pending the development of specialized readout electronics.

physics.ins-det↗

UV hybrid photon detector based on GaN photocathodes and Si low gain avalanche diode

Photon detectors featuring single-photon sensitivity play a crucial role in various scientific domains, including high-energy physics, astronomy, and quantum optics. Fast response time, high quantum efficiency, and minimal dark counts are the characteristics that render them ideal candidates for detecting individual photons with exceptional signal-to-noise ratios, at frequencies in the the range of hundreds of MHz. Here, we report on our first design and operational results on a Hybrid Photon Detector (HPD) that combines the high quantum efficiency of a Gallium Nitride (GaN) photocathode and the low noise characteristics of a Si-based Low-Gain Avalanche Diode (LGAD). This hybrid detection scheme has the potential to reach single-photon detection sensitivity with high quantum efficiency, low noise levels and capable of operating at hundreds of MHz repetition rates.

physics.ins-det↗

Spectroscopic performance of Low-Gain Avalanche Diodes for different types of radiation

Low-Gain Avalanche Diodes are a type of silicon Avalanche Photo-Diodes originally developed for the fast detection of minimum ionizing particles in high-energy physics experiments. Thanks to their fast timing performance, the Low-Gain Avalanche Diode paradigm enables detectors to accurately measure minimum ionizing particles with a timing resolution of a few tens of picoseconds. Such a performance is due to a thin substrate and the presence of a moderate signal gain. This internal gain of a few tens is enough to compensate for the reduced charge deposition in the thinner substrate and the noise of fast read-out systems. While Low-Gain Avalanche Diodes are optimized for the detection of minimum ionizing particles for high-energy particle detectors, it is critical to study their performance for the detection of different types of particle, such as X-rays, gamma-rays, or alphas. In this paper, we evaluate the gain of three types of Low-Gain Avalanche Diodes: two devices with different geometries and doping profiles fabricated by Brookhaven National Laboratory, and one fabricated by Hamamatsu Photonics with a different process. Since the gain in LGADs depends on the bias voltage applied to the sensor, pulse-height spectra have been acquired for bias voltages spanning from the depletion voltage up to breakdown voltage. The signal-to-noise ratio of the generated signals and the shape of their spectra allow us to probe the underlying physics of the multiplication process.

physics.ins-det↗

First survey of centimeter-scale AC-LGAD strip sensors with a 120 GeV proton beam

We present the first beam test results with centimeter-scale AC-LGAD strip sensors, using the Fermilab Test Beam Facility and sensors manufactured by the Brookhaven National Laboratory. Sensors of this type are envisioned for applications that require large-area precision 4D tracking coverage with economical channel counts, including timing layers for the Electron Ion Collider (EIC), and space-based particle experiments. A survey of sensor designs is presented, with the aim of optimizing the electrode geometry for spatial resolution and timing performance. Several design considerations are discussed towards maintaining desirable signal characteristics with increasingly larger electrodes. The resolutions obtained with several prototypes are presented, reaching simultaneous 18 micron and 32 ps resolutions from strips of 1 cm length and 500 micron pitch. With only slight modifications, these sensors would be ideal candidates for a 4D timing layer at the EIC.

physics.ins-det↗

Monolithic Active Pixel Sensors on CMOS technologies

Collider detectors have taken advantage of the resolution and accuracy of silicon detectors for at least four decades. Future colliders will need large areas of silicon sensors for low mass trackers and sampling calorimetry. Monolithic Active Pixel Sensors (MAPS), in which Si diodes and readout circuitry are combined in the same pixels, and can be fabricated in some of standard CMOS processes, are a promising technology for high-granularity and light detectors. In this paper we review 1) the requirements on MAPS for trackers and electromagnetic calorimeters (ECal) at future colliders experiments, 2) the ongoing efforts towards dedicated MAPS for the Electron-Ion Collider (EIC) at BNL, for which the EIC Silicon Consortium was already instantiated, and 3) space-born applications for MeV $γ$-ray experiments with MAPS based trackers (AstroPix).

physics.ins-det↗

Characterization of BNL and HPK AC-LGAD sensors with a 120 GeV proton beam

We present measurements of AC-LGADs performed at the Fermilab's test beam facility using 120 GeV protons. We studied the performance of various strip and pad AC-LGAD sensors that were produced by BNL and HPK. The measurements are performed with our upgraded test beam setup that utilizes a high precision telescope tracker, and a simultaneous readout of up to 7 channels per sensor, which allows detailed studies of signal sharing characteristics. These measurements allow us to assess the differences in designs between different manufacturers, and optimize them based on experimental performance. We then study several reconstruction algorithms to optimize position and time resolutions that utilize the signal sharing properties of each sensor. We present a world's first demonstration of silicon sensors in a test beam that simultaneously achieve better than 6-10 micron position and 30 ps time resolution. This represents a substantial improvement to the spatial resolution than would be obtained with binary readout of sensors with similar pitch.

physics.ins-det↗

4-Dimensional Trackers

4-dimensional (4D) trackers with ultra fast timing (10-30 ps) and very fine spatial resolution (O(few $μ$m)) represent a new avenue in the development of silicon trackers, enabling new physics capabilities beyond the reach of the existing tracking detectors. This paper reviews the impact of integrating 4D tracking capabilities on several physics benchmarks both in potential upgrades of the HL-LHC experiments and in several detectors at future colliders, and summarizes the currently available sensor technologies as well as electronics, along with their limitations and directions for R$\&$D.

physics.ins-det↗

Measurements of an AC-LGAD strip sensor with a 120 GeV proton beam

The development of detectors that provide high resolution in four dimensions has attracted wide-spread interest in the scientific community for several applications in high-energy physics, nuclear physics, medical imaging, mass spectroscopy as well as quantum information. In addition to high time resolution and thanks to the AC-coupling of the electrodes, LGAD silicon sensors can provide high resolution in the measurement of spatial coordinates of an incident minimum ionizing particle. Such AC-coupled LGADs, also known as AC-LGADs, are therefore considered as candidates for future detectors to provide 4-dimensional measurements in a single sensing device with 100$\%$ fill factor. This article presents the first characterization of an AC-LGAD sensor with a proton beam of 120 GeV momentum at Fermilab. The sensor consists of strips with 80 $μ$m width, fabricated at Brookhaven National Laboratory. The signal properties, efficiency, spatial, and time resolution are presented. The experimental results show that the time resolution of such an AC-LGAD is compatible to standard LGADs with similar gain, and that AC-LGADs can be segmented with fine pitches as standard strip or pixel detectors.

physics.ins-det↗

Evaluation of Radiation Hardness of High-Voltage Silicon Vertical JFETs

In the future ATLAS Inner Tracker, each silicon strip module will be equipped with a switch able to separate the high voltage supply from the sensor in case the latter becomes faulty. The switch, placed in between the HV supply and the sensor, needs to sustain a high voltage in its OFF state, to offer a low resistance path for the sensor leakage current in the ON state, and be radiation hard up to 1.2e15 neq/cm2 along with other requirements. While GaN JFETs have been selected as suitable rad-hard switch, a silicon vertical HV-JFET was developed by Brookhaven National Laboratory as an alternative option. Pre-irradiation results showed the functionality of the device and proved that the silicon HV-JFET satisfied the pre-irradiation requirements for the switch. To assess its suitability after irradiation, a few p-type HV-JFETs have been neutron irradiated at Jozef Stefan Institute (JSI, Ljubljana, Slovenia). This paper reports the static characterization of these irradiated devices and the TCAD numerical simulations used to get an insight of the physics governing the post-irradiation behaviour.

physics.ins-det↗

Fabrication and performance of AC-coupled LGADs

Detectors that can simultaneously provide fine time and spatial resolution have attracted wide-spread interest for applications in several fields such as high-energy and nuclear physics as well as in low-energy electron detection, photon science, photonics and imaging. Low-Gain Avalanche Diodes (LGADs), being fabricated on thin silicon substrates and featuring a charge gain of up to 100, exhibit excellent timing performance. Since pads much larger than the substrate thickness are necessary to achieve a spatially uniform multiplication, a fine pad pixelation is difficult. To overcome this limitation, the AC-coupled LGAD approach was introduced. In this type of device, metal electrodes are placed over an insulator at a fine pitch, and signals are capacitively induced on these electrodes. At Brookhaven National Laboratory, we have designed and fabricated prototypes of AC-coupled LGAD sensors. The performance of small test structures with different particle beams from radioactive sources are shown.

physics.ins-det↗

Development of a High Rate Front-end ASIC for X-ray Spectroscopy and Diffraction Applications

We developed a new front-end application specific integrated circuit (ASIC) for the upgrade of the Maia x-ray microprobe. The ASIC instruments 32 configurable front-end channels that perform either positive or negative charge amplification, pulse shaping, peak amplitude and time extraction along with buffered analog storage. At a gain of 3.6 V/fC, 1 $μ$s peaking time and a temperature of 248 K, an electronic resolution of 13- and 10 electrons rms was measured with and without a SDD sensor respectively. A spectral resolution of 170 eV FWHM at 5.9 keV was obtained with an $^{55}$Fe source. The channel linearity was better than $\pm$ 1 % with rate capabilities up to 40 kcps. The ASIC was fabricated in a commercial 250 nm process with a footprint of 6.3 mm x 3.9 mm and dissipates 167 mW of static power.

physics.ins-det↗