arXiv subjects

Markku Juntti

Publications and source records attributed to Markku Juntti.

At least 127 records · Page 7Linked to original sources

arXiv2020

Matrix Decomposition for Massive MIMO Detection

Massive multiple-input multiple-output (MIMO) is a key technology for fifth generation (5G) communication system. MIMO symbol detection is one of the most computationally intensive tasks for a massive MIMO baseband receiver. In this paper, we analyze matrix decomposition algorithms for massive MIMO systems, which were traditionally used for small-scale MIMO detection due to their numerical stability and modular design. We present the computational complexity of linear detection mechanisms based on QR, Cholesky and LDL-decomposition algorithms for different massive MIMO configurations. We compare them with the state-of-art approximate inversion-based massive MIMO detection methods. The results provide important insights for system and very large-scale integration (VLSI) designers to select appropriate massive MIMO detection algorithms according to their requirement.

cs.IT↗

arXiv2020

Challenges of AI in Wireless Networks for IoT

The Internet of Things (IoT), hailed as the enabler of the next industrial revolution, will require ubiquitous connectivity, context-aware and dynamic service mobility, and extreme security through the wireless network infrastructure. Artificial Intelligence (AI), thus, will play a major role in the underlying network infrastructure. However, a number of challenges will surface while using the concepts, tools and algorithms of AI in wireless networks used by IoT. In this article, the main challenges in using AI in the wireless network infrastructure that facilitate end-to-end IoT communication are highlighted with potential generalized solution and future research directions.

cs.NI↗

arXiv2020

Radio Localization and Mapping with Reconfigurable Intelligent Surfaces

5G radio at millimeter wave (mmWave) and beyond 5G concepts at 0.1-1 THz can exploit angle and delay measurements for localization, by the virtue of increased bandwidth and large antenna arrays but are limited in terms of blockage caused by obstacles. Reconfigurable intelligent surfaces (RISs) are seen as a transformative technology that can control the physical propagation environment in which they are embedded by passively reflecting EM waves in preferred directions. Whereas such RISs have been mainly intended for communication purposes, RISs can have great benefits in terms of performance, energy consumption, and cost for localization and mapping. These benefits as well as associated challenges are the main topics of this paper.

eess.SP↗

arXiv2020

Noncoherent Joint Transmission Beamforming for Dense Small Cell Networks: Global Optimality, Efficient Solution and Distributed Implementation

We investigate the coordinated multi-point noncoherent joint transmission (JT) in dense small cell networks. The goal is to design beamforming vectors for macro cell and small cell base stations (BSs) such that the weighted sum rate of the system is maximized, subject to a total transmit power at individual BSs. The optimization problem is inherently nonconvex and intractable, making it difficult to explore the full potential performance of the scheme. To this end, we first propose an algorithm to find a globally optimal solution based on the generic monotonic branch reduce and bound optimization framework. Then, for a more computationally efficient method, we adopt the inner approximation (InAp) technique to efficiently derive a locally optimal solution, which is numerically shown to achieve near-optimal performance. In addition, for decentralized networks such as those comprising of multi-access edge computing servers, we develop an algorithm based on the alternating direction method of multipliers, which distributively implements the InAp-based solution. Our main conclusion is that the noncoherent JT is a promising transmission scheme for dense small cell networks, since it can exploit the densitification gain, outperforms the coordinated beamforming, and is amenable to distributed implementation.

cs.IT↗

arXiv2020

Decision Triggered Data Transmission and Collection in Industrial Internet of Things

We propose a decision triggered data transmission and collection (DTDTC) protocol for condition monitoring and anomaly detection in the industrial Internet of things (IIoT). In the IIoT, the collection, processing, encoding, and transmission of the sensor readings are usually not for the reconstruction of the original data but for decision making at the fusion center. By moving the decision making process to the local end devices, the amount of data transmission can be significantly reduced, especially when normal signals with positive decisions dominate in the whole life cycle and the fusion center is only interested in collecting the abnormal data. The proposed concept combines compressive sensing, machine learning, data transmission, and joint decision making. The sensor readings are encoded and transmitted to the fusion center only when abnormal signals with negative decisions are detected. All the abnormal signals from the end devices are gathered at the fusion center for a joint decision with feedback messages forwarded to the local actuators. The advantage of such an approach lies in that it can significantly reduce the volume of data to be transmitted through wireless links. Moreover, the introduction of compressive sensing can further reduce the dimension of data tremendously. An exemplary case, i.e., diesel engine condition monitoring, is provided to validate the effectiveness and efficiency of the proposed scheme compared to the conventional ones.

eess.SP↗

arXiv2020

Channel Estimation for RIS-Aided mmWave MIMO Channels

A reconfigurable intelligent surface (RIS) can shape the radio propagation by passively changing the directions of impinging electromagnetic waves. The optimal control of the RIS requires perfect channel state information (CSI) of all the links connecting the base station (BS) and the mobile station (MS) via the RIS. Thereby the channel (parameter) estimation at the BS/MS and the related message feedback mechanism are needed. In this paper, we adopt a two-stage channel estimation scheme for the RIS-aided millimeter wave (mmWave) MIMO channels using an iterative reweighted method to sequentially estimate the channel parameters. We evaluate the average spectrum efficiency (SE) and the RIS beamforming gain of the proposed scheme and demonstrate that it achieves high-resolution estimation with the average SE comparable to that with perfect CSI.

eess.SP↗

arXiv2020

A Line-of-Sight Channel Model for the 100-450 Gigahertz Frequency Band

This paper documents a simple parametric polynomial line-of-sight channel model for 100-450 GHz band. The band comprises two popular beyond fifth generation (B5G) frequency bands, namely, the D band (110-170 GHz) and the low-THz band (around 275-325 GHz). The main focus herein is to derive a simple, compact, and accurate molecular absorption loss model for the 100-450 GHz band. The derived model relies on simple absorption line shape functions that are fitted to the actual response given by complex but exact database approach. The model is also reducible for particular sub-bands within the full range of 100-450 GHz, further simplifying the absorption loss estimate. The proposed model is shown to be very accurate by benchmarking it against the exact response and the similar models given by International Telecommunication Union Radio Communication Sector (ITU-R). The loss is shown to be within $\pm$2 dBs from the exact response for one kilometer link in highly humid environment. Therefore, the its accuracy is even much better in the case of usually considered shorter range future B5G wireless systems.

eess.SP↗

arXiv2019

Adaptive Beamforming Design for mmWave RIS-Aided Joint Localization and Communication

The concept of reconfigurable intelligent surface (RIS) has been proposed to change the propagation of electromagnetic waves, e.g., reflection, diffraction, and refraction. To accomplish this goal, the phase values of the discrete RIS units need to be optimized. In this paper, we consider RIS-aided millimeter-wave (mmWave) multiple-input multiple-output (MIMO) systems for both accurate positioning and high data-rate transmission. We propose an adaptive phase shifter design based on hierarchical codebooks and feedback from the mobile station (MS). The benefit of the scheme lies in that the RIS does not require deployment of any active sensors and baseband processing units. During the update process of phase shifters, the combining vector at the MS is also sequentially refined. Simulation results show the performance improvement of the proposed algorithm over the random design scheme, in terms of both positioning accuracy and data rate. Moreover, the performance converges to exhaustive search scheme even in the low signal-to-noise ratio regime.

eess.SP↗

arXiv2019

Large Intelligent Surface for Positioning in Millimeter Wave MIMO Systems

Millimeter-wave (mmWave) multiple-input multiple-output (MIMO) system for the fifth generation (5G) cellular communications can also enable single-anchor positioning and object tracking due to its large bandwidth and inherently high angular resolution. In this paper, we introduce the newly invented concept, large intelligent surface (LIS), to mmWave positioning systems, study the theoretical performance bounds (i.e., Cramér-Rao lower bounds) for positioning, and evaluate the impact of the number of LIS elements and the value of phase shifters on the position estimation accuracy compared to the conventional scheme with one direct link and one non-line-of-sight path. It is verified that better performance can be achieved with a LIS from the theoretical analyses and numerical study.

eess.SP↗

arXiv2019

On Unified Vehicular Communications and Radar Sensing in Millimeter-Wave and Low Terahertz Bands

Future smart vehicles will incorporate high-data-rate communications and high-resolution radar sensing capabilities operating in the millimeter-wave and higher frequencies. These two systems are preparing to share and reuse a lot of common functionalities, such as steerable millimeter-wave antenna arrays. Motivated by this growing overlap, and advanced further by the space and cost constraints, the vehicular community is pursuing a vision of unified vehicular communications and radar sensing, which represents a major paradigm shift for next-generation connected and self-driving cars. This article outlines a path to materialize this decisive transformation. We begin by reviewing the latest developments in hybrid vehicular communications and radar systems, and then propose a concept of unified channel access over millimeter-wave and higher frequencies. Our supporting system-level performance characterization relies upon real-life measurements and massive ray-based modeling to confirm the significant improvements brought by our proposal to mitigating the interference and deafness effects. Since our results aim to open the door to unified vehicular communications and radar sensing, we conclude by outlining the potential research directions in this rapidly developing field.

cs.NI↗

arXiv2018

Wireless Terahertz System Architectures for Networks Beyond 5G

The present white paper focuses on the system requirements of TERRANOVA. Initially details the key use cases for the TERRANOVA technology and presents the description of the network architecture. In more detail, the use cases are classified into two categories, namely backhaul & fronthaul and access and small cell backhaul. The first category refers to fibre extender, point-to-point and redundancy applications, whereas the latter is designed to support backup connection for small and medium-sized enterprises (SMEs), internet of things (IoT) dense environments, data centres, indoor wireless access, ad hoc networks, and last mile access. Then, it provides the networks architecture for the TERRANOVA system as well as the network elements that need to be deployed. The use cases are matched to specific technical scenarios, namely outdoor fixed point-to-point (P2P), outdoor/indoor individual point-to-multipoint (P2MP), and outdoor/indoor "quasi"-omnidirection, and the key performance requirements of each scenario are identified. Likewise, we present the breakthrough novel technology concepts, including the joint design of baseband signal processing for the complete optical and wireless link, the development of broadband and spectrally efficient RF-frontends for frequencies >275 GHz, as well as channel modelling, waveforms, antenna array and multiple-access schemes design, which we are going to use in order to satisfy the presented requirements. Next, an overview of the required new functionalities in both physical (PHY) layer and medium access control (MAC) layers in the TERRANOVA system architecture will be given. Finally, the individual enablers of the TERRANOVA system are combined to develop particular candidate architectures for each of the three technical scenarios.

cs.NI↗

arXiv2018

Energy Efficiency Fairness for Multi-Pair Wireless-Powered Relaying Systems

We consider a multi-pair amplify-and-forward relay network where the energy-constrained relays adopting time-switching protocol harvest energy from the radio frequency signals transmitted by the users for assisting user data transmission. Both one-way and two-way relaying techniques are investigated. Aiming at energy efficiency (EE) fairness among the user pairs, we construct an energy consumption model incorporating rate-dependent signal processing power, the dependence on output power level of power amplifiers' efficiency, and nonlinear energy harvesting (EH) circuits. Then we formulate the max-min EE fairness problems in which the data rates, users' transmit power, relays' processing coefficient, and EH time are jointly optimized under the constraints on the quality of service and users' maximum transmit power. To achieve efficient suboptimal solutions to these nonconvex problems, we devise monotonic descent algorithms based on the inner approximation (IA) framework, which solve a second-order-cone program in each iteration. To further simplify the designs, we propose an approach combining IA and zero-forcing beamforming, which eliminates inter-pair interference and reduces the numbers of variables and required iterations. Finally, extensive numerical results are presented to validate the proposed approaches. More specifically, the results demonstrate that ignoring the realistic aspects of power consumption might degrade the performance remarkably, and jointly designing parameters involved could significantly enhance the energy efficiency.

cs.IT↗

arXiv2018

When IoT Keeps People in the Loop: A Path Towards a New Global Utility

While the Internet of Things (IoT) has made significant progress along the lines of supporting individual machine-type applications, it is only recently that the importance of people as an integral component of the overall IoT infrastructure has started to be fully recognized. Several powerful concepts have emerged to facilitate this vision, whether involving the human context whenever required or directly impacting user behavior and decisions. As these become the stepping stones to develop the IoT into a novel people-centric utility, this paper outlines a path to materialize this decisive transformation. We begin by reviewing the latest progress in human-aware wireless networking, then classify the attractive human-machine applications and summarize the enabling IoT radio technologies. We continue with a unique system-level performance characterization of a representative urban IoT scenario and quantify the benefits of keeping people in the loop on various levels. Our comprehensive numerical results confirm the significant gains that have been made available with tighter user involvement, and also corroborate the development of efficient incentivization mechanisms, thereby opening the door to future commoditization of the global people-centric IoT utility.

cs.NI↗

arXiv2018

Energy-Efficient Transmission Strategies for CoMP Downlink - Overview, Extension, and Numerical Comparison

This paper focuses on energy-efficient coordinated multi-point (CoMP) downlink in multi-antenna multi-cell wireless communications systems. We provide an overview of transmit beamforming designs for various energy efficiency (EE) metrics including maximizing the overall network EE, sum weighted EE and fairness EE. Generally, an EE optimization problem is a nonconvex program for which finding the globally optimal solutions requires high computational effort. Consequently, several low-complexity suboptimal approaches have been proposed. Here we sum up the main concepts of the recently proposed algorithms based on the state-of-the-art successive convex approximation (SCA) framework. Moreover, we discuss the application to the newly posted EE problems including new EE metrics and power consumption models. Furthermore, distributed implementation developed based on alternating direction method of multipliers (ADMM) for the provided solutions is also discussed. For the sake of completeness, we provide numerical comparison of the SCA based approaches and the conventional solutions developed based on parametric transformations (PTs). We also demonstrate the differences and roles of different EE objectives and power consumption models.

cs.IT↗

arXiv2018

Energy Efficiency Maximization for C-RANs: Discrete Monotonic Optimization, Penalty, and l0-Approximation Methods

We study downlink of multiantenna cloud radio access networks (C-RANs) with finite-capacity fronthaul links. The aim is to propose joint designs of beamforming and remote radio head (RRH)-user association, subject to constraints on users' quality-of-service, limited capacity of fronthaul links and transmit power, to maximize the system energy efficiency. To cope with the limited-capacity fronthaul we consider the problem of RRH-user association to select a subset of users that can be served by each RRH. Moreover, different to the conventional power consumption models, we take into account the dependence of baseband signal processing power on the data rate, as well as the dynamics of the efficiency of power amplifiers. The considered problem leads to a mixed binary integer program (MBIP) which is difficult to solve. Our first contribution is to derive a globally optimal solution for the considered problem by customizing a discrete branch-reduce-and-bound (DBRB) approach. Since the global optimization method requires a high computational effort, we further propose two suboptimal solutions able to achieve the near optimal performance but with much reduced complexity. To this end, we transform the design problem into continuous (but inherently nonconvex) programs by two approaches: penalty and \ell_{0}-approximation methods. These resulting continuous nonconvex problems are then solved by the successive convex approximation framework. Numerical results are provided to evaluate the effectiveness of the proposed approaches.

cs.IT↗

arXiv2018

Energy-Efficient Multi-Cell Multigroup Multicasting with Joint Beamforming and Antenna Selection

This paper studies the energy efficiency and sum rate trade-off for coordinated beamforming in multi-cell multi-user multigroup multicast multiple-input single-output systems. We first consider a conventional network energy efficiency maximization (EEmax) problem by jointly optimizing the transmit beamformers and antennas selected to be used in transmission. We also account for per-antenna maximum power constraints to avoid non-linear distortion in power amplifiers and user-specific minimum rate constraints to guarantee certain service levels and fairness. To be energy-efficient, transmit antenna selection is employed. It eventually leads to a mixed-Boolean fractional program. We then propose two different approaches to solve this difficult problem. The first solution is based on a novel modeling technique that produces a tight continuous relaxation. The second approach is based on sparsity-inducing method, which does not require the introduction of any Boolean variable. We also investigate the trade-off between the energy efficiency and sum rate by proposing two different formulations. In the first formulation, we propose a new metric that is the ratio of the sum rate and the so-called weighted power. Specifically, this metric reduces to EEmax when the weight is 1, and to sum rate maximization when the weight is 0. In the other method, we treat the trade-off problem as a multi-objective optimization for which a scalarization approach is adopted. Numerical results illustrate significant achievable energy efficiency gains over the method where the antenna selection is not employed. The effect of antenna selection on the energy efficiency and sum rate trade-off is also demonstrated.

cs.IT↗

arXiv2018

Last Meter Indoor Terahertz Wireless Access: Performance Insights and Implementation Roadmap

The terahertz (THz) band, 0.1-10 THz, has sufficient resources not only to satisfy the 5G requirements of 10 Gbit/s peak data rate but to enable a number of tempting rate-greedy applications. However, the THz band brings novel challenges, never addressed at lower frequencies. Among others, the scattering of THz waves from any object, including walls and furniture, and ultra-wideband highly-directional links lead to fundamentally new propagation and interference structures. In this article, we review the recent progress in THz propagation modeling, antenna and testbed designs, and propose a step-by-step roadmap for wireless THz Ethernet extension for indoor environments. As a side effect, the described concept provides a second life to the currently underutilized Ethernet infrastructure by using it as a universally available backbone. By applying real THz band propagation, reflection, and scattering measurements as well as ray-tracing simulations of a typical office, we analyze two representative scenarios at 300 GHz and 1.25 THz frequencies illustrating that extremely high rates can be achieved with realistic system parameters at room scales.

cs.NI↗

arXiv2018

Terahertz Technologies to Deliver Optical Network Quality of Experience in Wireless Systems Beyond 5G

This article discusses the basic system architecture for terahertz (THz) wireless links with bandwidths of more than 50 GHz into optical networks. New design principles and breakthrough technologies are required in order to demonstrate Tbps data-rates at near zero-latency using the proposed system concept. Specifically, we present the concept of designing the baseband signal processing for both the optical and wireless link and using an end-to-end (E2E) error correction approach for the combined link. We provide two possible electro-optical baseband interface architectures, namely transparent optical-link and digital-link architectures, which are currently under investigation. THz wireless link requirements are given as well as the main principles and research directions for the development of a new generation of transceiver frontends, which will be capable of operating at ultra-high spectral efficiency by employing higher-order modulation schemes. Moreover, we discuss the need for developing a novel THz network information theory framework, which will take into account the channel characteristics and the nature of interference in the THz band. Finally, we highlight the role of pencil-beamforming (PBF), which is required in order to overcome the propagation losses, as well as the physical layer and medium access control challenges.

cs.NI↗